R, RD

Q: Archimedes Principle of Bouyancy

A:

Q:

A: Copper wire of diameter 2mm or 0.002 m The radius of the wire 0.001 m Stress in the wire is 80 GPa o...

Q:

A:

Q:

A:

Q:

A:

Q:

A: The normal force is the force acting in the axial direction of the beam. The shear force is the forc...

Q: Calculate the reactions at and A for the beam shown. The weight of the beam is 16 Ib/ft. 500 Ib 500 ...

A:

Q: Can evaporation from a reservoir be reduced? Explain the different methods.

A: Yes, evaporation from reservoirs can be reduced. Various measures need to be taken in order to reduc...

Q:

A: Projections of an object are 2D views of that object when seen from any of the sides. There are gene...

Q:

A: Using definitions 

Q:

A:

Q:

A: As per our guidelines we are supposed to answer only first question in case of multiple questions. K...

Q: rush

A: Given :- Radius, r1= 10cm r2= 5cm v1= 4m/s  

Q: a. Examine each of the following and determine the areas they are applicablei. Modulus of Rigidityii...

A:

Q:

A: Values of ground elevation: Horizontal Scale = 1/1000 Vertical Scale = 1/50 Elevation of road = 50....

Q: The followings statement is associated to the possible increase in tota stress at certain depth exce...

A:

Q: Subject: transportation engineering

A:

Q: Determine the absolute maximum moment on the steel bridge at joint C caused by the moving trailer ha...

A:

Q: P1) The engineer need to construct a Parshall Flume into 1.5m in wide rectangular channel to a speci...

A: Given:- width=1.5m crest = 0.25  To find:- suitable size of flume  

Q: A precast slab was employed for the floor of a building. The thickness and width of slab are 80 mm a...

A:  

Q: solve using virtual work method

A: To determine: a) Displacement at point C with directions b) Slope at D with directions

Q:

A: Given:- 5 storey building waste water runs= half full in the pipe To find:- diameter of horizontal d...

Q:

A: To determine the tensile cracks (Zo) -

Q:

A:

Q:

A:

Q: rush

A:

Q:

A: The fold is an OVERTURN FOLD with anticline and synclines.

Q:

A: Slack is defined as the difference between the latest allowable time and the earliest allowable time...

Q: Explain each, the diagrams below, draw the shear force and bending moment diagram of each.

A: Since we only answer up to first parts, we’ll answer the first one . Please resubmit the question an...

Q: A single-angle tension member 175 mm x 100 mm x 18 mm haw two gage lines in its long leg and one in ...

A: Area of the angular section(A)=4961 mm2, Tension member=175mm x 100mm x 18 mm, Fy=248 Mpa, Fu=400 Mp...

Q:

A:

Q: The topic is all about the different kinds of stresses the simple stress, simple normal stress, simp...

A:

Q: To prevent local buckling occurring, it is necessary to limit the outstand/thickness ratios fo nges ...

A: Due to shear in the web of I section a compressive force will be generated and that will cause local...

Q: Calculate the slenderness ratio of a short timber strut 2m long with cross-sectional area of 75mm × ...

A: Given data in question  Length of strut 2 m Cross sectional area Short timber strut To find out Slen...

Q:

A:

Q:

A: Hi! Thank you for the question. As per the honour code, we’ll answer the first question since the ex...

Q: Q1) Triaxial un drained tests were performed on clay samples taken from stratum shown below (point A...

A: Given: Triaxial undrained tests were performed on clay samples taken from stratum shown below Find...

Q: Problem I. With the ongoing extension of Manila Skyway, a series of 250 mm diameter circular poles a...

A: Circular pole diameter(d)=250 mm, Hight of the pole=3 m, Unit weight of the pole=22 kN/m3, Load(P) a...

Q:

A: h1=0.9% h2=0.5% offset, s=30 m RL of ground at point of intersection, RLc=40 m N=0.9+0.5=1.4 %

Q:

A: Introduction : SYBU JavaScript Blocker is a Google Chrome Extension that prevents the browser from l...

Q: Questions: a).What is the difference between error, warning and notes in staad? b). The question is ...

A: Introduction : You've constructed a material with a lower Young's modulus than concrete, which is a ...

Q: Design a square footing using 25 mm main bars and 75 mm clear cover assuming an allowable soil press...

A: Solution

Q: A 50.0-m-tall hollow aluminum flagpole is equivalent in strength to a solid cylinder 4.00 cm in diam...

A: Given data in question  Length of pole 50 m Diameter  4 cm Force 800 N To find out How far top of po...

Q: Q2) Find the increasing stress (Ao) at point A, at depth 6 m below the corner of the footing of foun...

A: Solution

Q: P? Using appreximate hetked of analysis, find the internal forees at sec. a-a and sec.b-b and Sec. c...

A:

Q: 450 N B 30 30 30 6.196 m 5.196 m 450N Treating horizontal reaction at A as redundant, what is the ho...

A:

Q:

A: when two curves meet each other, according to their gradient they defines under the category of summ...

Q: Evaluate the role of civil society in the local development council using citizen's participation as...

A: Introduction : Civil society, also known as the "space where we act for the common good," aims to co...

Q: HW3: LOS of Basic Freeway Given: » Four-lane freeway (2 in each direction) » Lane width =11 ft Right...

A: Traffic congestion is a condition in transport that is characterised by slower speeds, longer trip, ...

Q:

A: Given data: R.L of known of B.M=170.850 m R.L of computed B.M =170.858 m C=10