R1 Consider the balanced bridge shown next. R2 Assuming that C,= C3, R, = R2 = R3 = 1 k0, and that the bridge is operating at a frequency of 1kHz, then the capacitance C, is approximately found to be (mF) Detector 250 500 160 None of the choices 3:34 PM 330 Consider the balanced bridge SHOWN IN THE FIGURE OF THE OTHER BRIDGE QUESTION Assuming that C,= C3, R, = R2 R3 = 1 kQ, and that the bridge is operating at a frequency of 1kHz, then R4 is approximately found to be (in Ohms) Answer this question please 2k 1k 0.5k None of the choices 1.5k 3:34 PM mm 나 O O O

R1 Consider the balanced bridge shown next. R2 Assuming that C,= C3, R, = R2 = R3 = 1 k0, and that the bridge is operating at a frequency of 1kHz, then the capacitance C, is approximately found to be (mF) Detector 250 500 160 None of the choices 3:34 PM 330 Consider the balanced bridge SHOWN IN THE FIGURE OF THE OTHER BRIDGE QUESTION Assuming that C,= C3, R, = R2 R3 = 1 kQ, and that the bridge is operating at a frequency of 1kHz, then R4 is approximately found to be (in Ohms) Answer this question please 2k 1k 0.5k None of the choices 1.5k 3:34 PM mm 나 O O O

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

Which of the following method is used for the measurement of Medium Resistance?a) Kelvin’s double bridge methodb) Carey-Foster bridge methodc) Anderson Bridged) Direct-Deflection method
Using Maxwell’s (mesh) Loop method, determine the mesh currents IA, IB, IC, ID
Consider the load convention that is used for the RLC elements shown in Figure 2.2 of the text. A. If one says that an inductor absorbs zero real power and positive reactive power. is it (a) True (b) False B. If one says that a capacitor absorbs zero real power and negative reactive power (or delivers positive reactive power), is it (a) False (b) True C. If one says that a (positive-valued) resistor absorbs (positive) real power and zero reactive power, is it (a) True (b) False
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
The simultaneous equations representing the currents flowing in an unbalanced, three-phase, star connected, electrical network are as follows: 2.4I1 + 3.6I2 + 4.8I3 = 1.2 −3.9I1 + 1.3I2 − 6.5I3 = 2.6 1.7I1 + 11.9I2 + 8.5I3 = 0 Using Gaussian elimination, solve the equations for the currents.
Compute the 8 – point I.D.F.T of x(n) = { 10,-2+ 2j,-2,-2- 2j, 10,-2+ 2j, -2,-2- 2j} using Phasor plot of twiddle factor to compute the DFT please check the numbers before answering
Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
Solve the power triangle at Z6 using the following network laws below.1.) Kirchoff's Law2.) Maxwell Equation3.) Nodal Analysis Given:V1, V2, and V3 = 220∠0° V, 50 HzZ1 = 7+j8 ohmsZ2 = 6+j3 ohmsZ3 = 5+j5 ohmsZ4 = 2+j3 ohmsZ5 = 8+j4 ohmsZ6 = 1+j9 ohms
1) Referring to the circuit as in Figure 1, transform the circuit in phasor domain representation.2) Determine the value of total impedance, ZT3) Determine the value of total current, IT4) Determine the value of branch current, I1 and I25) Determine the value of voltage across resistor, R1, R2 and R36) Determine the value of voltage across capacitor, C1 and C27) Determine the value of voltage across inductor, L.
Node Voltages Method (Nodeanalysis) to obtain step-by-step circuit equationand write in matrix format. R1=1/6 R2=1/2
Discuss why a. Complex power in an AC circuit is more than the DC resistance. b. Receiving end voltage of an unloaded long line may be more than sending end voltage. c. Inductance of the three phase of a transmission line are generally not equal. d. It is necessary to use the geometric means radius in the formula for the inductance calculation whereas the formula for the capacitance calculation uses the actual radius.
What is the difference between Mesh and Nodal analysis, what and are their advantages and disadvantages