R2 VCC 24V R1 2600 MP SA06 Vin -OV Fig.1 Transistor Switch Procedure: 1. Determine the value of base bias resistor of a transistor switch that will drive a DC motor represented by a 600 resistor R1. The motor has a rated working voltage of 24 v and will be driven by MPSA05 an NPN transistor. The control signal of Ov and 5v will come from an Arduino developmental board.

R2 VCC 24V R1 2600 MP SA06 Vin -OV Fig.1 Transistor Switch Procedure: 1. Determine the value of base bias resistor of a transistor switch that will drive a DC motor represented by a 600 resistor R1. The motor has a rated working voltage of 24 v and will be driven by MPSA05 an NPN transistor. The control signal of Ov and 5v will come from an Arduino developmental board.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.2P

See similar textbooks

Similar questions

Explain the operation of the circuit by drawing the AC power control (regulation) circuit with the triac and the waveforms of the voltage at the load ends.
10.a. The type of stepper motor that has a pair of center-tapped windings is theA. closed-loop stepper motor.B. unipolar stepper motor.C. reactive stepper motor.D. center-biased stepper motor.10.b. The type of transistor configuration that’s used with a DC servo motor is theA. emitter-follower configuration.B. H-bridge configuration.C. totem pole configuration.D. negative-logic configuration.
If a sinusoidal voltage is applied to the base of a biased npn transistor and the resulting sinusoidal collector voltage is cut to near zero volts, what is the state of the transistor? Please select one: a. answers B and C b. interrupted drive c. answers A and C d. forced into nonlinear operation e. drifting into saturation
1-Design an ON-OFF transistor switch to control a 12 volt DC motor rotation. 2- What is the application of ON-OFF transistor switch? 3- What is the operation regions of ON-OFF transistor switch on characteristic? 4- How we can make sure that the transistor work in ON state or OFF state?
Find the RL and IL value range that will keep the output of the zener circuit in the figure constant at 10 Volts.
A 10-bit analog to digital converter has a reference voltage of 8 Volts. (i) Find the digital output if the input voltage is 6.875 Volts? (ii) What should be the required input to get an output of 1110101001?
What is the operation of a Zener voltage regulator? How it works?
Design the heatsink for the power transistor of a voltage regulator, keeping the heatsink cost minimal.The voltage regulator has an output voltage of 5 V and full load current of 500 mA. At full load, the regulator efficiency is 25 %, with the power transistor contributing to 45% of the power loss. The regulator is expected to operate at ambient temperature of between 20 °C and 40 °C. The heatsink temperature should not be more than 80 °C. Assume the cost of the heatsink is inversely proportional to the value of the thermal resistance θSA. The power transistor has the following parameters:θJC = 3 °C /WTJ,max = 150 °CDetermine the thermal resistances, θCS and θSA.
Explain the operating principle of power factor correction circuit that can shape the AC input current and regulate the output voltage at the same time. If necessary, the figure of the PFC control loop can be drawn to help explain the idea.
The circuit diagram of step-up type DC-DC converter is given below. It is assumed that the output capacitor is large enough and the output voltage is constant. (Consider that there is no circuit losses.) What should the inductance value be for the circuit to always operate in Continuous Current Mode (CCM)? Calculate.
a) In given regulator circuit, zener voltage is 4.2V and zener power is Pw is 105mW. Calculate R1 resistor value range to circuit work correctly. b) What is the advantage of using a transistor zener regulator circuit instead of a given regulator circuit? Briefly explain.
Answer the following. Use a detailed explanation. 1. In reverse bias condition, what happens to the current if the temperature increases 10 degrees Celsius. 2. What semiconductor is frequently used for its high reliability at high speed? 3. What type of rectifier circuit has the highest dc output?