ratio a: 1. Let vs(t) = 7000cos(21t) V, R1 = 252, R2 = 602 C = 3µF, L1 = 50mH and oa= 5. Compute the primary coi time-dependent voltage vi (t) (that is, the voltage of node 1) and the primary current i (t). %3D An ideal transformer circuit. R, LVS HVS Node 1 R Report the peak value of V V Report the phase of V1: rad Report the peak value of I1:mA report the phase of I: rad ref

ratio a: 1. Let vs(t) = 7000cos(21t) V, R1 = 252, R2 = 602 C = 3µF, L1 = 50mH and oa= 5. Compute the primary coi time-dependent voltage vi (t) (that is, the voltage of node 1) and the primary current i (t). %3D An ideal transformer circuit. R, LVS HVS Node 1 R Report the peak value of V V Report the phase of V1: rad Report the peak value of I1:mA report the phase of I: rad ref

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.3P: Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source...

See similar textbooks

Similar questions

You are given five light bulbs designed to operate on 160 mA current at 3.0 V (rms values), arid want to connect them in parallel, through an ideal transformer, to 120 V rms AC household power. a) Draw a circuit diagram showing the AC power source (a generator symbol ), the transformer, and resistors for the light bulbs. b) Is the required transformer step-up or step-down? What turns ratio N5/N is needed? e) Calculate the ruts current through both the primary and secondary coils of the trans former, in mA.
1.The equivalent parameters of a 150kVA, 2400V/240V transformer, are R1=0.2Ω, R2=2mΩ, X1=0.45Ω, X2=4.5mΩ, Rc=10kΩ, and Xm=1.55kΩ. The transformer is operating at rated load and rated voltage with 0.8 lagging power factor. Using the approximate equivalent circuit referred to the primary side, determine: (i) (i) the voltage regulation (ii) (ii) the transformer power loss and efficiency 2.Nanoscale drives occur in the living world for example in the bacterial flagellum or ATP synthase. For one of these drives describe with the aid of diagrams how it operates and discuss the features which the drive has in common with large scale, man-made counterparts. 3.A 15 kW, 250V shunt motor with Ra=0.22 Ω, Rf=170 Ω. At no-load and rated voltage, the speed is 1200 rpm and the armature current is 3 A. At full-load and rated voltage, the line current is 55A. What is the full-load speed?
A 2.4-kVA, 2400/240-V, 50-Hz, step-down transformer has the followingparameters: R, = 1.5 a, X, = 2.5 R, R, = 0.02 a, X, = 0.03 Q, R,, = 6 kR,and X,, = 8 kR. It is operating at 80% of its load at unity power factor.Using the exact equivalent circuit embodying the ideal transformer, determine the efficiency of the transformer. Also sketch its phasor diagram.
Consider an ideal transformer with N1 ¼ 3000 and N2 ¼ 1000 turns. Let winding 1 beconnected to a source whose voltage is e1ðtÞ ¼ 100ð1 jtjÞ volts for 1a ta 1 ande1ðtÞ ¼ 0 for jtj > 1 second. A 2-farad capacitor is connected across winding 2. Sketche1ðtÞ, e2ðtÞ, i1ðtÞ, and i2ðtÞ versus time t
Neon signs (which often contain gases other than neon) use high voltage to excite gaseous atoms that then give off a characteristic glow. When plugged into a wall outlet (120 V AC), a typical neon sign transformer delivers 400 W AC at a voltage of 18 kV rms. The primary coil has 400 turns. 1. First, what is the number of turns in the secondary to achieve this high voltage? Give your answer to 2 significant digits. 2. Next, if the transformer is ideal, what is the rms current in the primary? Give you answer in amps with 2 significant digits. 3. Finally, what is the rms current in the secondary? Give your answer in milli-amps with 2 significant digits.
The Transformer is a device used to change voltage into the designated desired voltage to fit an application. Transformer also is one of the most important electrical device widely used in today’s everyday life. An ideal transformer is the one worked with 100% efficiency. However, in reality, a transformer may not achieve 100% efficiency. a) Draw a transformer principle element. b) Explain the working principle of a transformer. c) Identify the parameter that remains unchanged whenever the transformer is in operation and explain why it remains unchanged. d) With the help of a sketch, identify where all the losses happen and their type in a transformer. e) What is the difference between modern and old mobile phone charger,
The equivalent parameters of a 150kVA, 2400V/240V transformer, are R1=0.2Ω, R2=2mΩ, X1=0.45Ω, X2=4.5mΩ, Rc=10kΩ, and Xm=1.55kΩ. The transformer is operating at rated load and rated voltage with 0.8 lagging power factor. Using the approximate equivalent circuit referred to the primary side, determine: (i) the voltage regulation (ii) the transformer power loss and efficiency Please refer to the answer
SUBJECT: Elements of Electrical Machines DesignINSTRUCTIONS: - Please write clearly and understandable way. - Write all the corresponding Given with their corresponding symbols and units. - Draw/Illustrate the diagram/circuit or drawings that is related to the problem, IF POSSIBLE, which is HIGHLY REQUIRED. - Solve in step-by-step, no shortcut - Underline twice the Final Answer.PROBLEM: When does the polarity of a transformer become significant?
A 120:480-V, 10-kVA step-up two-winding transformer is to be used as an autotransformer to supply a 120-V circuit from a 600-V source (a step-down autotransformer). When it is tested as a two-winding transformer at rated load, unity power factor, its efficiency is 97.9 %. 1.Show the connection diagram of the transformer converted as an autotransformer and identify which is the series winding Nse and the common winding Nc.
A 10 kVA, 500/250 V, single phase transformer has its maximum efficiency of 94% when delivering 90% of its rated output at unity p.t. Estimate its efficiency when delivering its full load output at p.t. of 0.8 lagging,
As given in the figure, an ideal transformer with a 2: 1 winding ratio is fed from a 240 Volt source with an internal impedance of 8 + j6 Ω and transfers maximum power to the load impedance connected at its secondary. So, which of the following is the V2 voltage in the secondary?
An ideal transformer is rated to deliver 460 kVA at380 V to a customer, as shown in Figure.a. How much current can the transformer supply tothe customer?b. If the customer’s load is purely resistive (i.e., ifpf = 1), what is the maximum power that thecustomer can receive?c. If the customer’s power factor is 0.8 (lagging),what is the maximum usable power the customercan receive?d. What is the maximum power if the pf is 0.7(lagging)?e. If the customer requires 300 kW to operate, what isthe minimum power factor with the given sizetransformer?