Recall the following circuit from Problem Set 2: Consider the following circuit. A 0.25 ul capacitor is in series with two resistors. R, = 1500 Q and R2 = 3500 Q. Find the amplitude and phase of the voltage across each component. The peak current through the circuit is I, = 2 mA and its angular frequency is w = 180 rad/s. R. a) What is the average power dissipated by the resistors? b) What is the average power supplied by the source? c) Explain the relationship between these results.

Recall the following circuit from Problem Set 2: Consider the following circuit. A 0.25 ul capacitor is in series with two resistors. R, = 1500 Q and R2 = 3500 Q. Find the amplitude and phase of the voltage across each component. The peak current through the circuit is I, = 2 mA and its angular frequency is w = 180 rad/s. R. a) What is the average power dissipated by the resistors? b) What is the average power supplied by the source? c) Explain the relationship between these results.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The average value of a double-frequency sinusoid, sin2(t+), is given by (a) 1 (b) (c) Zero
An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
Find the ff. on the AC circuit below having a 120Vrms as a signal source V1. a.) Total Impedance ZT b.) Current Ic , IL & IR c.) Current Total IT d.) Phasor angle e.) Voltage across each branch. VR, Vc, VL f.) Draw the phasor diagram of the circuit with complete label. g.) Plot the sinusoidal wave indicating the phase angle, showing which are lagging or leadingNote: (see attached image for the diagram and question. please answer it based on your knowledge. thank you so much!)
Find the ff. on the AC circuit below having a 120Vrms as a signal source V1. a.) Total Impedance ZT b.) Current Ic , IL & IR c.) Current Total IT d.) Phasor angle e.) Voltage across each branch. VR, Vc, VL f.) Draw the phasor diagram of the circuit with complete label. g.) Plot the sinusoidal wave indicating the phase angle, showing which are lagging or leadingNote: (see attached image for the diagram. please answer it based on your knowledge. thank you so much!)
If a current 5.0 A lags the applied voltage 230 V by an angle ϕ, it can be resolved into two components, OA in phase with the voltage and OB lagging by 90°. If the phasor diagram in to a circuit possessing resistance and inductance in series, OA and OB must not be labelled and respectively. It has become the practice to say that the power factor is laggingwhen the current lags the supply voltage, and leading when the current leads the supply voltage. This means that the supply voltage is regarded as the reference quantity. (a) A 30 μ F capacitor is connected across the applied voltage, 50 Hz supply. Calculate the reactance of 30 μ F capacitor connected across applied voltage (b) the reactance of the capacitor; (c) the current.
The graph of the vs sign applied to the circuit in the figure is given above. The switch works ideally in the circuit Switch; When the applied input signal is positive, it becomes closed. Current flows through it) In the applied input signal, Vp = 12V, R = 10ohm, T = lms. According to this; a) Find the mean and rms values of the output voltage? b) Find the average input power and output power and calculate its efficiency. c) If we consider that there is a voltage drop of 1V on the switch; c.1) Calculate the average and rms values of the output voltage, c.2) Average input power and output power c.3) Efficiency.
A 29-Ω television and an 16-Ω amplifier are connected in series across a 158-V source of voltage from an outlet. A 34-Ω light bulb is also connected across the 133-V source and is in parallel with the series combination. (a) Determine the total rms current supplied by the voltage source. A (b) Determine the total average power supplied by the voltage source.
Q6: An AC source operating at 60 Hz with a maximum voltage of 170 V is fed to a series combination of1.2kΩ resistor and 2.5μF capacitor connected in a timer circuit. How can you evaluate the maximumcurrent in the circuit? Can you estimate the rms value potential difference across each circuit element?Compare the power factor of this timer circuit with a circuit contain only ohmic resistance. Justify youranswer?
Calculate the R value in ohms, since the 13kHz frequency sinusoidal sign is observed at the output of the circuit in the picture. (C=10nF)
The 9 Ω resistor in the circuit is replaced with a variable impedance Zo. Assume Zo is adjusted for maximum average power transfer to Zo. 1. a) What is the maximum average power that can be delivered toZo?2. b) What is the average power developed by the ideal voltage sourcewhen maximum average power is delivered to Zo?3. c) Choose single components from Appendix H to form animpedance that dissipates average power closest to the value in part(a). Assume the source frequency is 60 Hz.
For the circuit in the figure below, determine the load impedance that maximizes the average power drawn from the circuit in the figure below. What is the maximum average power?
In a 220 Vrms, 50 Hz. Source, determine the following values: V peak and the trigonometric equation, The period, T and ω, V at 8 ms,V at 14 ms, T when V = 200 V in the 1st cycle (2 values), T when V = -150 V in the 1st cycle (2 values)