Required information Determine the magnitude of the forces. In the given figure, y = 300 N, V2 = 1.6 m, and V3 = 11 m. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. v1 30 60 V2 V3 Compute the x and y components of each force acting on element 2. (RAx)2 =| (RAy)2 =| (RBx)2 (RBy)2 = (RCx)2 (RCy)2 =| |N |N |N IN IN

Required information Determine the magnitude of the forces. In the given figure, y = 300 N, V2 = 1.6 m, and V3 = 11 m. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. v1 30 60 V2 V3 Compute the x and y components of each force acting on element 2. (RAx)2 =| (RAy)2 =| (RBx)2 (RBy)2 = (RCx)2 (RCy)2 =| |N |N |N IN IN

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.15P: The structure is supported by a pin at C and a cable attached to A. The cable runs over the small...

See similar textbooks

Similar questions

Find the internal force systems acting on sections 1 and 2.
The 50-ft measuring tape weighs 2.4 lb. Compute the span L of the tape to four significant figures.
Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo is unloaded by a container handling crane. Each bollard is fastened to the wharf using anchor bolts. Three cables having known tension force magnitudes F, = ll0 kN.F, = 85kN.and F, 9OkNare secured to one bollard at a point A with coordinates (0.0.45 m. 0) in the x-r-: coordinate system shown in the figure part b. Each cable force is directed at an attachment point on the ship. Force F, is directed from point A to a point on the ship having coordinates (3 m, 9 m. 0) force F, is directed at a point with coordinates (6.5 m. 8.5 m. 2 m) and force F, is directed at a point with coordinates (8 m. 9 m. S m). The diameter of each anchor bolts is 4 24 mm. (a) Find the reaction forces and reaction moments at the base of the bollard. (b) Calculate the average shear stress in the anchor bolts (in the x-: plane). Assume each bolt cart ics an equal share of the total force.
1) Given the figure below, answer the following questions: a) What are the x and y components offorce F? (use Fx and Fy)b) What are the x and y components offorce P? (use Px and Py)(Hint: The x-y plane is differentfrom the true horizontal and verticalaxes)c) What are the vertical and horizontalcomponents of force F? (use Fh & Fv)d) What are the vertical and horizontalcomponents of force P? (use Ph & Pv)e) What is the magnitude of the resultant?f) What angle does the resultant make withthe horizontal axisg) What angle does the resultant makewith the inclined x-axis.
Passing an exploratory section through the body and exposing the internal forces acting on the exploratory section, Pxz represents Shear Force parallel to x-axis. T or F
What would be the maximum weight W of the block, shown in the following figure, so that the tension developed in any cable does not exceed 100 N
Physics for Engineering A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0, respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the left end where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) and the weight (W) of the bar. (Hint: Formulate three equations for the three unknowns, 2 equations for the 1st condition and 1 equation for the 2nd condition.)
1) Determine the horizontal and vertical components of reaction at A(Ax,Ay) . Express your answers in newtons to three significant figures separated by a comma 2) Determine the force in the cable BC . Express your answer to three significant figures and include the appropriate units.
Please help. Please make sure you clearly state how you got the numbers you got and why you are using them. Also please make sure you clearly put your formulas and label your units along the numbers that you are using. In the following frame ilustration, F1s 60 N and F2 is 9 N. What is the tension in the cable AB and the reaction force vector necessary to keep the system in static equilibrium? Give the X component reaction force at C( for an x axis going left to right). Also please solve for the rest of the 3 unknowns please. Thank you
Find the tension in each of the supporting cables in the figure when the weight of the crate is 500 newtons.
Consider the frame shown in (Figure 1). Suppose that F1 = 6 kN . Determine the magnitude of the force in member FD. Determine the magnitude of the force in member DB. Determine the x and y components of reaction the pin C exerts on member ABC using scalar notation. Determine the x and y components of reaction the pin C exerts on member EDC using scalar notation.