Review Water flows at 25 ft³/s in the channel, which is originally 6 ft wide and then gradually narrows to b2 = 4.5 ft . The original depth of water is 3 ft. (Figure 1) Part A Determine the depth y2 after it passes through the constriction. Express your answer to three significant figures and include the appropriate units. HÀ ? y2 = Value Units Submit Request Answer Figure < 1 of 1 > Part B What width bɔ will produce critical flow y2 = yc? Express your answer to three significant figures and include the appropriate units. 6 ft HÀ ? b2 = Value Units 3 ft Submit Request Answer

Review Water flows at 25 ft³/s in the channel, which is originally 6 ft wide and then gradually narrows to b2 = 4.5 ft . The original depth of water is 3 ft. (Figure 1) Part A Determine the depth y2 after it passes through the constriction. Express your answer to three significant figures and include the appropriate units. HÀ ? y2 = Value Units Submit Request Answer Figure < 1 of 1 > Part B What width bɔ will produce critical flow y2 = yc? Express your answer to three significant figures and include the appropriate units. 6 ft HÀ ? b2 = Value Units 3 ft Submit Request Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Read the question carefully and give me all solutions. A concrete-lined canal (n=0.015) having one side vertical and other side is sloping at 2H:1V carries a discharge of 8.5 m3/s with velocity of 0.65 m/s. Determine the following; a. Dimensions of the canal (bottom width, normal depth and free-surface width) b. Bed slope c. Total construction cost per unit length of the canal if the cost of excavation is Php 120/m3 and the cost of channel lining is Php 360/m2
QUESTION 1 a) what is conveyance factor K ? b) Figure below shows a trapezoidal channel and its dimensions. The channel also has bottom slope of 0.0036 and side slope of 1.5 (H): 0.75 (V). Determine the value of Chezy resistance coefficient C and velocity of flow if flow rate is 10 m^3/s.
*hydraulics *use handwritten A rectangular channel 5.50 m wide and 1.30 m deep is laid on a uniform slope of 0.002. The roughness coefficient of the channel is 0.013. 1.) Which of the following most nearly gives the rate of flow in the channel in m^3/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67 2.) Which of the following most nearly gives the saving’s in lining per meter length of channel that could have been offered by using the most efficient rectangular section but adhering to the same flow capacity and slope in m^2/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67 3.) Which of the following most nearly gives the savings in earth excavation per meter length of channel that could have been offered by using the most efficient rectangular Section but adhering to the same flow capacity and slope in m^3/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67
A steep rectangular channel is to carry flow rate of 1.90 m3/s wirh a slope of 0.01 and roughness coefficient of 0.011, for a minimum area of the material to use, compute: Depth if the channel in m 0.15 1.51 1.15 0.51 Width of the channel in m .30 1.02 3.02 2.30 Area of the steel material to be used if the channel is 3m 4.56 0.52 0.45 6.12
The flowrate per unit width (q = Q/b) in a wide rectangular channel is q = 4 m2/s. Is the flow subcritical or supercritical if the depth is: (a) 0.8 m, (b) 3.2 m? Show all calculations.
Please give me right solution An irrigation canal with trapezoidal cross-section has the following elements: bottom width = 1.00 m., depth of water = 0.50 m., side slope 1.5 horizontal to 1 vertical, slope of canal bed = 0.001, coefficient of roughness = 0.025. The canal will serve clay-loam rice land. Determine the discharge?
A channel has been designed to convey clear water to a fish hatchery. The design calls for aflow depth of 2.0 ft and a velocity of 2.0 ft/s. The channel is very wide so the side effects canbe neglected and the hydraulic radius taken as equal to the depth. It is to be constructed insand which has a median diameter ds = 0.915 mm (0.003 ft). For a flat bed in this materialthe Darcy-Weisbach friction factor is estimated to be f = 0.0185 and the required channelslope is S = 0.000145. The water temperature is 20°C and the kinematic viscosity υυ is = 1.08x 10-5 ft2/s. The specific gravity of the sand is 2.65. Clear water is admitted to the channeland it is imperative that no material be scoured from the bed since any sand in the hatcherywill result in instantaneous death of all the fish. Using Shields' diagram, determine if theexisting design is adequate to deliver clear water to the hatchery.
Given a canal with 1 to 1 side slopes and cross-sectional area of 10 m2. Find the dimensionsfor the best hydraulic cross-section. Answer: depth = 2.35 m, bottom width = 1.92m I need solution. Thanks!
3. If the canal described in previous problem (Problem 1) were permitted to grow weeds on the sides and bottom, what would be the velocity and discharge? Use n= 0.40. Problem 1: 1. Consider a farm irrigation ditch in a loam soil having the following dimensions: a) Bottom width, 0.5 meters. b) Total depth, 0.60 meters. c) Side slopes of 1 horizontal to 1 vertical. d) Depth of water, 0.40 meters. Find the following properties: a) Cross-sectional area of the stream. b) Wetted perimeter. c) Hydraulic radius of the stream.
In the Given Rectangular Dam, determine the magnitude of the resultant R and where itintersects the base AB. !!!(please show different solution not the other one i asked a while ago, i cant understand those written there)!!!
a rectangular canal is 5.7m wide and 1.4m deep has a roughness coefficient of 0.013 and is laid on a slope of 0.002. what is the savings in lining (per meter length of canal) if the most efficient section is used for the same discharge? Answer: 0.632 m3/s
HYDRAULICS Convert all units in SI. Round off to 2 significant figures. A contracted rectangular weir 10 ft long is built in the center of a rectangular chanel 20 ft wide. How high is the weir iff the depth of water upstream is 3.50 ft when the discharge is 40 cfs?