RL2=152.5 Q4). The following staff readings in meter were obtained when leveling along the center line of natural ground of a road. The elevation of grade line at station 0+00 is rade Line RL 148.4 m and elevation of grade line at station 3+20 is 152.3 m. Find height of cut and depth of fill at each station. Recorded data are in. 3.2 Station BS Time: 3 hrs.

RL2=152.5 Q4). The following staff readings in meter were obtained when leveling along the center line of natural ground of a road. The elevation of grade line at station 0+00 is rade Line RL 148.4 m and elevation of grade line at station 3+20 is 152.3 m. Find height of cut and depth of fill at each station. Recorded data are in. 3.2 Station BS Time: 3 hrs.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

- In reciprocal leveling across a deep ravine the following sets of rod readings were taken: Instrument set-up near A : BS on A = 1.719m, FS on B = 2.578m Instrument set-up near B : BS on A = 1.335m, FS on B = 2.176m Point A has a known elevation of 197.428m. Determine the elevation of point B.
From the following differential leveling notes, compute the difference in elevation between stations 5 and 6. a. 2.62 b. 1.61 c. 3.51 d. 1.87
Reduce the set of differential leveling notes in Table 2-11, and perform the arithmetic check. -Adjust the elevation of BM K110. The length of the level run was 780 m, with setups that are equally spaced. The elevation of BM 132 is 187.536 m.
An engineer's level with stadia constant of 0.30-m was set up on the line between A and B, the following crosshair readings were observed. If the stadia interval factor of the level is 100, determine the length of line AB.
A line of levels is run from BM1 to BM2, which is 12 km long. Elevation of BM1 was found out to be 100 m and that of BM2 is 125.382 m. Average backsight and foresight distance were 150 m and 100 m respectively. if the average backsight reading is 3.4 m and every time it is taken, the rod is inclined to the side from vertical by 4°, what should be the corrected elevation of BM2?
RECIPROCAL LEVELING. In reciprocal leveling across a deep ravine the following sets of rod readings were takent: Instr Near A: BS on A=1.719 m, Average Fs on B=2.578 m Instr Near B: Average BS on A=1.335 m, FS n B=2.176 m Point A is on one side of the ravine and has a known éle- vation of 197.428 m. Point B is on the other side. Deter- mine the elevation of point B.
prove the formula of the combined correction for earths curvature and refraction Hcr = 0.0675 D^2 where: Hcr= combined correction D = horizontal distance
Fundamentals of Surveying In leveling across a river, reciprocal level readings were taken between two points A & B. From a set-up near A on A, 0.954 &0.952m, on B 2.086, 2.087, 2.088 & 2.087 m. At the setup near B: on B, 2.450 and 2.448m, on A, 1.362, 1.363, 1.364 & 1.363m What the Elevation at B if Elev at A is 45.75m?
For all the computed values with decimals, use four (4) digits after the decimal. Differential leveling runs from BM10 to BM11 at a distance of 7.5 km. It was observed that the leveling rod was inclined 6° from the vertical every time the backsight is taken. The average BS reading is 3.15m and the average length per set-up is 300m. Determine the error every 300m set-up and the correct elevation of BM11 if the recorded elevation was 173.20m.
A line of levels is run from BM1 to BM2, which is 12 km long. Elevation of BM1 was found out to be 100 m, and that of BM2 is 125.382 m. Average backsight and foresight distance were 150 m and 100 m, respectively. If the average backsight reading is 3.4 m, and every time it is taken, the rod is inclined to the side from vertical by 4 degrees. What should be the corrected elevation of BM2?
An inverse method of leveling is executed between two existing concrete structures and across a concrete wall located midway between the two structures. All rod readings, as indicated in the sketch, were taken with the rod held upside down. From the data portrayed, if the elevation of A (bottom of the concrete beam of the first structure) is 240.05 m., the elevation of the bottom of the concrete beam of the second structure (indicated as C) should be
A differential leveling loop began and closed on BM Tree (elevation 323.48 ft). The plus sight and minus sight distances were kept approximately equal. Readings (in feet) listed in the order taken are 3.18 1 +S2 on BM Tree, 4.76 1 -S2, and 2.44 1 +S2 on TP1, 3.05 1 -S2 and 6.63 1 +S2 on BM X, 3.64 1 -S2 and 2.35 1 +S2 on TP2, and 3.07 1 -S2 on BM Tree. Prepare, check, and adjust the notes.