Rotation of bar OA is controlled by the lead screw which imparts a horizontal velocity v to collar C and causes pin P to travel along the smooth slot. Determine the values of and dot theta where r= overline OP if h = 160mm x = 120mm and v = 25mm / s at the instant represented.

Q: Flash floods will occur ....... A. when the soils have a high infiltration capacity…

A: Reference : Geo technical Engineering, Flood and types of floods. Given : A multiple choice question…

Q: I'm still confused on your solution could you go over each step again but in more detail. Like for…

A: Given: Required: To explain the reaction equations calculated by previous expert. To explain why x…

Q: A rectangular channel is 3.0-in wide and carries a discharge of 3.30 m³/s at a depth of 0.9 m. A…

A: Given: Width of rectangular channel at upstreamB=3 in B=3×0.0254B=0.0762 m DischargeQ=3.3 m3s Depth…

Q: The supporting beams for the pool deck in Fig.1 are designed as simply supported with effective span…

A: Solution:-

Q: A beam with the cross-section shown is subjected to a vertical shear of 28 kN. Determine: (a) the…

A:

Q: A rolled I-section beam is supported on a 75 mm wide bearing plate as shown in the figure. Thickness…

A: Given Data  Width of support (a) = 75 mm  Thickness of flange (tf) = 20 mm  Thickness of web (tw) =…

Q: Water flows from a large tank through a large pipe that splits into two smaller pipes as shown in…

A: Given : To Determine :

Q: 1. Method of Joints: Find AB AC BD and BC (edited) 9 ft 9 ft A B -18 ft 18 ft- C 18 18 ft- D 6 kips…

A: Given: A simply supported symmetrically loaded truss with hinge support at A and roller support at…

Q: A soil has a bulk density of 22 kN/m³ and water content of 10%. The dry density of soil is: a) 18.6…

A:

Q: confused on how you are applying muller breslau principle to solve this problem. Could you explain…

A: Given a statically determinate beam in which ILDs have to be drawn using Muller Breslau principle.…

Q: 2. For each of the plane stress states listed below find the three principle stresses and the…

A: Given data:- a) σx=20 kpsi, σy=-15 kpsi, τxy=8 kpsi cw b)σx=16 kpsi, σy=10 kpsi, τxy=5 kpsi cww c)…

Q: 3. The soil profile at a site for a proposed building is shown in the following figure. The density…

A: Given Data: The data is given as: Over consolidated ratio of clay(OCR)=1.5Initial void…

Q: A simply supported beam of span 6 m carries an ultimate UDL of 25 kN/m. The plastic moment capacity…

A: Given Data: Span L = 6m Uniformly Distributed Load =25kN/m To Determine: Plastic Moment Capacity.

Q: Solve the slope and deflection of the compound beam shown at point E which is located 3m to the…

A: Given: A compound beam  Required: Slope and deflection at point E using conjugate beam method

Q: Determine the resultant internal loadings on the cross section through point D. Assume the reactions…

A: Given data : Determine the resultant internal loading on cross section through point D ?

Q: Given truss a.) compute the reactions Ay, Gy force b.) det. the at bars BC, A B 300 с 32m D ✓100kn…

A:

Q: What are the Numerical aspects of CFD(for Computational fluid dynamics ) and what is meant by…

A: Fluid:- A substance is said to be fluid if it continuously flows (deforms) when shear stress is…

Q: Q.2) A simple beam of span length 3.2 m carries a uniform load of intensity 48 kN/m. The cross…

A: Given Data : Span = 3.2m Uniform load intensity = 48 kn/m Wood flanges Properties : E = 10 GPa Size…

Q: Problem-05, A section line AB appears to be 10.16 cm on a photograph for which the focal length is…

A: Given data- Appeared length AL=10.16 cm, Focal length f=16 cm, Length on map ML=2.54 cm, Scale…

Q: GIVEN A sluice gate across a channel of width b is shown in the closed and open positions in Figs.…

A: Anchoring force required to hold the Sluice gate in place

Q: Briefly discuss the characteristics of Figure 7.4 in May’s textbook.

A: Given data- A contour map from Santa Monica Freeway Surveillance system given. To Find- The…

Q: The beam is subjected to the internal moment of M = 2.6 kN?m Determine the maximum bending stress…

A: Given : M = 2.6 kN-m Determine the max. bending stress developed in the beam ?

Q: Problem 4: Consider again Problem 3 with a constant pressure gradient (Fig. 5) in the x-direction…

A: A flow profile with a constant pressure gradient along x is given. The flow is between the two…

Q: 200 lb Part A 100 lb/ft 4 ft 300 lb-ft ---10-- Draw the shear diagram for the shaft. The support at…

A:

Q: In a typical concrete mix, the sand particles occupy roughly 30% of the concrete volume. If the bulk…

A:

Q: When 1 cm on a map represents 10 m on the ground, the representative fraction of the scale is: (a)…

A: Given data : Distance on map = 1cm and distance on ground = 10m  Find : Representative fraction…

Q: Determine the absolute maximum sheur & moment in the simply Supported bridge shown in fig, due to…

A:

Q: Determine the tension, T, in the cable support which is attached at point B, and also the l'artesian…

A: Objective: To determine the tension in the cable and the Cartesian components of the reaction at A.…

Q: 6.2. KN 27-2 kN/m 12 M design loads 4M B

A: Given: Solve for the beam deflection

Q: A 6m El = constant E = 50 GPa I= 135(106) mm² 70kN-m Determine the slope and deflection at point b…

A:

Q: The average speed of vehicles on an expressway is being studied. a. Suppose observation on 50…

A: Given,n=50sample mean, x¯=65 km/hrstandard deviation, σ=6 km/hrto determine,the two-sided 99%…

Q: Q4 Draw the influence lines for (a) the vertical reaction at B, (b) the shear just to the right of…

A:

Q: 4. Given: Vicat test data for a cement paste sample, Find: a. The initial set time, b. The final set…

A:

Q: Calculate the axial force, shear force and bending moment at point B on the parabolic arch. 80 KN A…

A: Given data:-

Q: Sorry for so many questions but why do we divide it by 2? It's the only thing that's keeping me from…

A: Given: AR (h2 /2)=Ar(h/2)  Required: To explain why (divided by 2) is done.

Q: 16-36. At the instant shown, the shaft and plate rotates with an angular velocity of w = 14 rad/s…

A:

Q: PARKING STUDIES PROB 1. Data collected at a parking lot indicate that a total of 300 cars park…

A: Space Hours of Demand: The space hours of demand are the computation of the total hours at which…

Q: In the figure below, Gate A/B/C is 1 m square and is hinged at B.  Calculate the depth of water…

A: Given: Side of the gatea=1 m Area of the gateA=1 m2 From the figure, the fluid is water. Therefore,…

Q: Draw the compaction curve using the following given data from a standard Proctor test. 2. From…

A: Objective: To draw the compaction curve for the given Standard Proctor Test results, and determine…

Q: Determine (a) the magnitude of the counterweight W for which the maximum absolute value of the…

A: Given data : Introduction : 1 - According to the problem we have to determine Magnitude of…

Q: For #5-7, assume there is a creek with a width of 4.6 m, depth of 23 cm, slope of 0.001 m/m, and…

A: Given data:- The given creek width is, 4.6 m The given depth is, 23 cm. The given slope is, 0.001m/m…

Q: If the sampler tube is pushed at the bottom of the bore hole to a distance of 585 mm with length of…

A: Given- Penetration length=585 mm, Recovered length=535 mm,

Q: The beam is loaded as follows: ● Downward distributed load that varies in intensity from 10 N/m at…

A: Given: Required: Moment at fixed support Vertical reaction at fixed support Load diagram Note: as…

Q: 3. An unconfined aquifer has a hydraulic conductivity of 25 mm/sec. There are two observation wells…

A:

Q: A camera with a focal length of 20 cm fitted in an aircraft is used for taking vertical aerial…

A: Given data: Focal length, f=0.2 m Elevation of terrain, h = 1200 m Scale, S=18000

Q: 200 N R₂ 100 N/m linge 80

A:

Q: Problem No. 1 A flexible pavement for an urban interstate highway is to be designed using the AASHTO…

A: AASHTO Method: The design of flexible pavement is carried out using the AASHTO method in which…

Q: Please help me. how to get Girder Moments Just answer one question!  Using Factor Method, determine…

A: To determine- Girder moments.

Q: 6. An initially rectangular element of material is deformed as shown in the figure (note that the…

A:

Q: A twin cam, 32 valve, 4-stroke, 8 - cylinder SI engine operates at (4000 rpm), find: the rate a cam…

A: