rovide a design outlining the ideal refrigerant and operating parameters for a direct contact heat exchanger-type cascade refrigeration system that will run with a 150 Tons load at -40°C evaporator and 65°C condensing temperatures. Imagine that your isentropic compression is 74% effective.Draw the engaging temperature as well so that the heat exchange interfaces differ by 5°C. please draw and explain

rovide a design outlining the ideal refrigerant and operating parameters for a direct contact heat exchanger-type cascade refrigeration system that will run with a 150 Tons load at -40°C evaporator and 65°C condensing temperatures. Imagine that your isentropic compression is 74% effective.Draw the engaging temperature as well so that the heat exchange interfaces differ by 5°C. please draw and explain

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.3DP

See similar textbooks

Similar questions

When a standard-efficiency air-cooled condenser is used, the condensing refrigerant will normally be higher in temperature than the entering air temperature.
Provide a technical design outlining the ideal refrigerant and operating parameters for a three-stage closed-type cascade refrigeration system that will run with a 150TOR load at -40°C evaporator and 65°C condensing temperatures. Imagine that your isentropic compression is 74% effective.Draw the engaging temperature as well so that the heat exchange interfaces differ by 5°C. Please draw detailed. explain and show solution. what are the refrigerants that is ideal? why?
Provide a technical design outlining the ideal refrigerant and operating parameters for a three-stage closed-type cascade refrigeration system that will run with a 150TOR load at -40°C evaporator and 65°C condensing temperatures. Imagine that your isentropic compression is 74% effective.Draw the engaging temperature as well so that the heat exchange interfaces differ by 5°C. Please draw detailed. explain and show solution. what are the refrigerants that is ideal? why? Please. It would be a great help. (not satisfied with the answer a while ago?
3)A cascade refrigeration system uses R22 in the low temp unit and R12 in the high temp unit. The system develops 30 kW of refrigeration at -40C. The R12 system operates at -10C evaporating temp and 38C condensing temp. There is a 10 degree overlap of temperatures in the cascade condenser. Calculate the (a) mass flow rate of R22, (b) mass flow rate of R12, (c) the power required by R22 compressor, and the power required by R12 compressor.
Sketch a commercial type outdoor air-cooled condenser. Discuss the heat transfermechanism in the said condenser.
Provide a technical design outlining the ideal refrigerant and operating parameters for a three-stage closed-type cascade refrigeration system that will run with a 150TOR load at -40°C evaporator and 65°C condensing temperatures. Imagine that your isentropic compression is 74% effective.Draw the engaging temperature as well so that the heat exchange interfaces differ by 5°C. Please draw detailed. explain Please. It would be a great help.
Concentric Tube Heat Exchanger Why was it difficult to achieve steady-state conditions?
A parallel Flow heat exchanger designed to heat fuel oil from 90℃ to 130℃, while the heating fluid enters at 160℃ and leaves 140℃. Calculate AMTD. ANSWER: 20℃
In a certain refrigeration system for low temperature application, a two-stage operation is desirable which employs ammonia system that serves a 40 − ton evaporator at −30°C. The system uses a direct contact cascade condenser, and the condenser temperature is 40°C. Sketch the schematic diagram of the system and draw the complete process on the PH diagram b. The mass flow rate in the low loops in kg/s c. The mass flow rate in the low and high pressure loops in kg/s d. The total work
Explain the meaning and usefulness of the effective diameter (a type of equivalent diameter) for the annular region in a double pipe heat exchanger?
‌A Cascade refrigeration system using R-32 and a heat exchanger is operating an evaporator with a capacity of 6 tons at a temperature of -30°C. If the heat exchanger pressure is 0.80 MPa and the condensing temperature is 50°C, determine the COP and the refrigerating efficiency of the system. Draw the schematic diagram of the system and assume ideal conditions.
A counterflow concentric tube heat exchanger is used to cool the lubricating oil from a large gas turbine engine. The flow rate of cooling water through the inner tube (Di = 25 mm) is 0.2 kg/s, while the flow of oil through the outer annulus (Do = 45 mm) is 0.1 kg/s. The oil and water enter at temperatures of 100°C and 30°C respectively. What is the heat transfer rate, and the overall convective heat transfer coefficient between fluids? Assuming negligible heat loss in the surrounding and negligible tube wall resistance and how long must the tube be made if the required outlet temperature of the oil is 60°C? (Cp oil = 2131 J/kg K, Cp water = 4187 J/kg K, hi = 2250W/m2K, ho = 38.8 W/m2K)