s a simple cantilever beam internally and externally determinate structure? Why?

Q: A bookshelf is made by placing a wooden plank on two brick supports. Where should the bricks be…

A: In the given problem, the weight of the books is not specify so consider the distributed weight of…

Q: Example 22.16. Draw the shear force and the bending moment diagrams for the simply Rarted beam…

A: Shear force diagram represents shear force at every section of the beam. Shear force at any…

Q: Encastré beams, similar to that in Figure 3, are usually used in performance in resisting shear…

A:

Q: What is the bending stress occurring in a square cross section beam with a side of 8 cm, which is…

A:

Q: B.M. at the free end of a cantilever beam subjected to any type of load is

A: A cantilever beam is a beam with fixed support at one end and other end is kept free .   Figure of…

Q: QUESTION 2 The composite beam loaded with a triangular distributed load , consists of two aluminum…

A: EAl = 70 GPA EW = 12 GPA Maximum deflection = 12 mm

Q: How do you calculate the maximum bending moment that a beam can resist?

A: The maximum bending moment that a beam can resist is also known as Moment of resistance (MR). Moment…

Q: Does a negative moment tend to bend the beam concave downwards? why?moment tends he beam concave…

A: Bending moment at any cross section of the beam is equal to the algebraic sum of couples and moments…

Q: Consider how the bending moment distorts a small element of the beam located along the beam's…

A: Given Data: The bending moment acting on the beam is Take an elemental section of infinitesimal…

Q: Required Information A cantilever beam experiences a point load at its free end (Point A). The…

A: Given data : P=3 KN L=3 m Width (b)=9 cm Depth (h)=20 cm

Q: Direct formula for single beam element??

A:

Q: Definitions of these terms in the context of a square section cantilever beam: Uniaxial stress:…

A: In the context of a square section cantilever beam, Uniaxial stress are the stress acting along only…

Q: Using Area Moment Method: A simply supported beam AB is shown. Assume EI is constant 1. What is the…

A:

Q: The diameter of the cross section of the beam is increased, explain its effect on maximum bending…

A:

Q: is the bending moment at the free end of a cantilever beam when it carries uniformly distributed…

A:

Q: A beam one end fixed and with no support at the other end is known as    a. Cantilever Beam b.…

A: Solution:

Q: Figure shows a beam made from material A and material B. If it is known that the allowable bending…

A: For the Given composite beam  EA = 200 GPa EB = 100 GPa σA = 180 MPa σB = 60 MPa   To determine the…

Q: What is the maximum shear force, when a cantilever beam is loaded with uniform distributed load…

A: Given data: Cantilever beam loaded with UDL Find Maximum shear force

Q: Is a simple cantilever beam externally determinate structure?

A: Externally determinate are those structures whose no. Of unknowns are equal to no. Of equations.

Q: A cantilever beam of rectangular cross- section is subjected to load at free end. If the depth of…

A:

Q: Briefly discuss the importance of establishing the sign convention in representing the internal…

A: The shear and bending moment diagrams are mainly used to determine the critical sections of the beam…

Q: A beam which has part of the loaded beam extends outside the support is called a O a. Freely…

A: Correct Option: d. Over hanging beam.

Q: Which is the expression for the neutral axis of a beam subjected to pure bending about z axis?

A:

Q: Choose correct answer: In a cantilever beam, the shear force value at the free end is Negative…

A: Beam Beam is structural element of an engineering which can be useful for various applications such…

Q: Determine the reactions and draw the shear and bending moment diagrams for the four-span continuous…

A: Uniformly distributed load is the load which is continuously and uniformly distributed over the…

Q: Which is the formula for determination for the equation of the neutral axis in the critical cross…

A: Solution:

Q: For the T-beam formed by welded structural steel plates, assume that it has: linearly elastic…

A: Given data as per the question Load =9000 kg Calculations  Now using parallel axis theorem Moment of…

Q: Describe what are beams? Give an example?

A: Given Beams To find Definition of beam, with example

Q: What does the stress in a composite beam depend on? O the modulus of elasticity of both materials…

A:

Q: Normally the cross section of a beam is first designed to resist theallowable bending stress.True or…

A: Cross-Section The cross-section is taken perpendicular to the longitudinal axis of the bar. All the…

Q: Why is it difficult to solve the equation for the deflection of the beam?

A:

Q: Why do the Engineers purposely design composite beams?

A: The composite material is a combination of two or more different materials with different chemical…

Q: Why do the actual bending and shear stress in the beam do not exceed allowable limits?

A: Given Actual bending stress Actual shear stress To find State why actual bending stress and shear…

Q: Can the beam's shear and moment diagrams be helpful in determining the maximum shear and moment in…

A: The formula of the shear force of a beam is, F=dM(x)dx. Where 'M(x)' is the bending moment of the…

Q: What is a beam-column?

A: The beam will subjected to transverse load. The column is subjected to compressive load.

Q: Why is the discontinuity functions method advantageous for solving the problems involving beams or…

A: The discontinuity function method is one of the important method to find the deflection of any…

Q: What is the difference between cantilever and fixed beams? (Explain in no more than 200 words)

A: 1. In case of cantilever beam, one end of the beam is fixed whereas Fixed beams are fixed at both…

Q: To delermine the Intenal moments within a cantsiever beam that has two dferent crosssectional areas…

A:

Q: Does a positive internal moment tend to bend the beam concave upwards?why?

A: Let's assume a simply supported beam of length L. Then calculate the reactions on both the…

Q: Discuss the limitations of the superposition method and the conjugate beam method. Between the two…

A: The load at any location on the conjugate beam is equal to the bending moment at that position…

Q: Why does the moment in a beam generally vary along its length?

A: The moment in a beam generally varies along its length due to the presence of shear force in the…

Q: Part B - Maximum shear force Determine the maximum shear force, Vmax, in beam ABC. Express your…

A: givenpoint load PB=85kNtotal length of beam L=10ma=5mI corss sectionb=75mmc=150mmd=110mme=75mmsimply…

Q: . To design a beam why do we require applications of shear and flexure formulas?

A: To design a beam we need to find out the bending moment and shear force  And these two quantities…

Q: What happens when the internal shear or moment in the beam is maximum?

A:

Q: is the bending moment at the fixed end of a cantilever beam. Select

A: Ans-b. Maximum