S-curve model of diffusion: (true/false) and reasoning a. k = 0, the rate of diffusion is instantaneous? b. fixed k ≥ 0, the carrying capacity is determined only by the ratio of a and b? c. fixed k ≥ 0, the rate of diffusion is determined only by the ratio of a and b? please provide crt ans do not copied from another web site

S-curve model of diffusion: (true/false) and reasoning a. k = 0, the rate of diffusion is instantaneous? b. fixed k ≥ 0, the carrying capacity is determined only by the ratio of a and b? c. fixed k ≥ 0, the rate of diffusion is determined only by the ratio of a and b? please provide crt ans do not copied from another web site

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.27P

See similar textbooks

Similar questions

Determine the simplest equation based on the image Note : Option D. other option false
Calculate drift current density in 1.5 mm long slab of intrinsic Si at room temperature under applied voltage 10V? Assume carrier mobility of 1100 cm2 V-1 s-1. ..
The hydraulic diameter of a rectangular duct is calculated using the equation Dh = 4 A/p, where Dh is the hydraulic diameter, A is the cross-sectional area of the duct and p is the perimeter of the duct. If the dimensions of the rectangular duct are a = 20 cm ±0.4 mm, and b = 33 cm ±1.8 mm, what is the uncertainty of Dh in percentage format? Enter the answer as a numerical value without any sign. Retain 3 significant figures.
φ (x, y) = Kx^4 + y^4 - 6x^2 y According to the potential equation of a two-dimensional flow in the horizontal plane defined as; i-) What should be the K coefficient for the current to be physically possible? Show ii-) Is this current irregular? Show it. iii-) Determine the current function ψ (x, y) of this current. {ψ (0,0) = 0} iv-) Calculate the resultant velocity at point A (e, f) in this flow field. v-) Calculate the flow rate passing between the streamlines ψ (a, 1) and ψ (c, 1).
A sharp-edge orifice 5 cm diameter in the vertical side of a large tank discharges under a head of 5 m. if c = 0.98 cc = 0.62, determine: a) The diameter of jet at vena contracta, b) The velocity of jet at vena contracta, and c) The discharge in m/s.
1 - A square chip, with side ? = 5 mm, operates under isothermal conditions.The chip is positioned on a substrate so that its side and bottom surfaces are thermally insulated, while its top surface is exposed to theflow of a refrigerant at ?∞ = 15°C. From reliability considerations, the chip temperature cannot exceed ? = 85°C. The refrigerant being air, with a convection heat transfer coefficientcorresponding ℎ = 200 W/(m2K), what is the maximum allowable power for the chip? Since the coolant is a dielectric liquid for which ℎ = 3000 W/(m2K), what is the maximum allowed power?
To which of the following questions does an engineering economy analysis provide useful input? (a) Has the mechanical or electrical engineer chosen the most economical motor size given functional requirements? (b) Has the civil or mechanical engineer chosen the best thickness for insulating a building?(c) Has the biomedical engineer chosen the best materials for the company’s artificial knee product?(d) All of the above
In a spherical electrode system, gas material with the most favorable arrangement in terms of puncture resistance, outer radius r2 = 3.2 cm, puncture field strength Ed=75kV/cm and dielectric constant Ergas=1 is used. According to this;a) Calculate the inner radius of the electrode and the puncture voltage of the system according to the geometrical characteristics of the most suitable arrangement in terms of puncture resistance.b) Draw the puncture curve in the p-Emax plane for a voltage of U=40kV provided the outer radius is kept constant and indicate the boundaries of the inner sphere radii on the curve.c) Briefly interpret the electrode system in terms of discharge events in the geometric characteristics of p=0.8, p=1.8 and p=5 on the puncture curve.
Answer the problem Format (given, required, solutions include free body diagram.)
A thin insulator rod of mass m and length L=40 cm, as shown. thresholdon the surface of the plane and in an outer bend from the rails placed on the edges. It slides frictionlessly with a constant velocity of V=0,8 m/s. Itrails at the lower edge of the inclined plane. to each other with a rail parallel to the bar connected so that the bars and rails are closed, a rectangular frame they form. Rail plane is Ɵ=50° angle with horizontal plane (xz plane) is doing. Before the rod begins to weld, it must be tilted above the inclined plane. It stood above the lower edge of the plane at a distance of S=4m. Inclined plane and the rod shows a magnetic field of uniform B=0,5i+0,8j+0,20k(T) is under the influence. When the bar starts to slide, at t=3s moments the bar, the edge magnetic passing through the frame surface formed by the rails and the rails at the bottom edgewhat is flux?
Consider the translational mechanical network system shown on the figure. A 1-lb force, f(t), si applied at t=0. If fv=1, find K and M such that the response is characterized by a 3-sec settling time and a 2-sec peak time. Also, what is the resulting %OS?
Landmark trilateration employing reference beacons is used to locate the (x, y) coordinates of a robot. The location of landmark number 1 (P1) is at the origin and the location of landmark number 2 (P2) is on the x axis at a positive distance x2 away from the first landmark (that is, P1 coordinates are (0, 0), and P2 coordinates are (x2, 0). The robot is at location (xR, yR), which will be determined based on the information provided below. Find the robot location (xR, yR) given the following: x2 = 25.3 m (where x2 represents the distance between the landmarks) d1 = 53.7 m (where d1 is the distance between the robot and landmark number 1) d2 = 48.2 m (where d2 is the distance between the robot and landmark number 2) Be sure to find the xR coordinate of the robot location and find both possible values of the yR coordinate of the robot location