24. Given in the accompanying sketch are the observed forward and back bearings of an open compass traverse, the adjusted forward bearing of line BC is? 25. In question 24, the adjusted back bearing of line BF is? 24. Given in the accompanying sketch are the observed forward and back bearings of anopen compass traverse, the adjusted forward bęaring of line BC is?75 2564°00')20 63 50'39 0'01.6E91.0D25. In question 24, the adjusted back bearing of line BF is?

on looking at the noticed orientation of lines , it will be seen that contrast among back and front…

Answered: s traverse, the adjusted forward…

Engineering

Civil Engineering

s traverse, the adjusted forward bearing of line BC is?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The 1986 disaster in the former Soviet Union at the Chernobyl nuclear power plant explosion sent abo...

Q: PROBLEM NO. 1: MEMBER GF OF THE PIN – CONNECTED TRUSS IN FIG. 1 HAS A CROSS - SECTIONAL AREA OF 1548...

Q: A professional team of players is designing a catapult to launch a small balM at A so that it lands ...

Q: Question 8 What is the contract delivery method called where the prime consultant is responsible to ...

A: Brief concept introduction- Project delivery system- It is a system that gives permission to an agen...

Q: Two sets of size analysis results are available for a given material. From a Gaudin-Schuhmann plot, ...

A: Case a and b Size vs mass% is given So we will first calculate% retained

Q: Drill pipes are one of the most important components in drilling operations. Drill pipes are subject...

A: Given data- The given data of the question is shown in the below diagram- Length of the drill pipe-...

Q: 2) During heavy traffic congestion, it was observed that the average spacing of vehicles in queue in...

A: The number of vehicles occupying a unit length of road at a given time is expressed in vehicles per ...

Q: The rigid bar ABC shown in the figure below is hinged at A and supported by a steel rod at B. Determ...

Q: 52. Which type of inspection is more intensive involving examination of structural elements? A. O Mi...

Q: - Which type of inspection is more intensive involving examination of structural elements?

A: which type of inspection is more intensive involving examination of structural elements? Answer: Ma...

Q: for the figure shown, determine the reaction at B in kN

Q: Bar BC is made of brass which has E = 90 GPa, a = 20 × 10¯6 /°C, and A = 500 mm² Bar ED is made of s...

Q: Prob. 2.2-6. The three-part axially loaded member in Fig. P2.2-6 consists of a tubular segment (1) w...

Q: For the figure shown, determine the reaction at Bin kN. 60 N 10KNAU 3m 15m 1n 30° 630 370 560 ロ 210

Q: Chapter 2, Problem 2/086 Five forces are applied to the beam trolley as shown. Determine the y-coord...

Q: From the Figure, determine the minimum length of the curve. Assume a=11.2 ft/sec² and perception-rea...

A: a = 11.2 ft/s2 t = 2.5s v = 65 mph = 95.333ft/s (unit of speed is not given so considering as mile p...

Q: If the coeffof vastafron f ramfal values at 4 rangauge statfons s 30%. O mean ramfall is 10 % , theu...

Q: 5/103 Find the reaction at A due to the uniform loading and the applied couple. 2 kN/m 12 kN-m A 3 m...

A: Here vertical component of reaction at the point A is Ay, horizontal component of reaction at point ...

Q: 3.6 A 4-m-long rigid body carrying a 10-kN/m uniformly distributed load is supported by a pinned con...

A: given data is length of bar=4m to find the free body diagram and the reaction force at A also to fin...

Q: 1. Explain the following; a. What is Engineering Data Analysis? b. Differentiate Nominal from O...

A: a)Engineering data analysis is the resolution of information into simpler elements by the applicatio...

Q: What single payment at the end of year 5 is equivalent to an equal annual series of payment of $800 ...

Q: A horizontal parallel plate ESP consists of a single duct 4.8m height and 6m long with 30cm plate to...

Q: For the beam shown in the figure, Determine the following unknowns where L1 = 5m, L2 = 3m, and the m...

Q: Problem 3( smooth pipes in series. The entrance and exit to and from the reservoir are flush and sub...

Q: (2) Estimate the SDI for the following filtered wastewater samples. If the water is to be treated wi...

A: The test time in minutes, and the volume filtered in ml is given. The formula for silt density index...

Q: Two sets of size analysis results are available for a given material. From a Gaudin-Schuhmann plot, ...

Q: Chapter 2, Problem 2/086 Five forces are applied to the beam trolley as shown. Determine the y-coord...

Q: A submersible pump is pumping water from a well that is 200 ft of water through a 4 inch PVC pipe. T...

A: To Find ; (a) Static Head (b) Total Head

Q: A 1.2 m. wide wall footing was constructed on the surface of a silty sand soil. If the bottom of the...

Q: Question 4: Consider the beam cross-section shown below. Calculate the yield curvature. f: - 30 MPa ...

A: Solution: d=300 mm; b = 250 mm; fc = 30 MPa; fy = 400 MPa εe,=-0.000350 MPa Es = 200,000 MPa Ec = 5...

Q: A constant force F is applied for 3 s to change the particle's velocity from v1 to v2. Determine the...

A: To determine the force F responsible for the given change in velocity. NOTE: The solution is made ...

Q: A car bumper is designed to bring a 1800 kg car to a stop from a speed of 2.23 m/s while deforming 1...

A: Given:- m=1800kg Car stop from 2.23 m/s to zero, while deformation is 150mm Initial velocity u=2.23 ...

Q: The resultant of the force system shown is a 50-lb ft counterclockwise couple. Find forces P, Q, and...

A: To find value of P,Q,C

Q: A trunk of a car has a listed luggage capacity of 18 ft3 . Express the capacity in in3 , m3 , and cm...

A: Given: The luggage capacity is 18 ft3.

Q: Calculate the moment (positive if counterclockwise, negative if clockwise) of the 370-N force on the...

A: Since it is required to find the moment of the 370 N force on the handle of the wrench about the cen...

Q: Determine the centroid of the composite area shown in Fig.Q2.

A: The centroid of the composite area shown in Fig Q2 has to be determined

Q: Determine the resultant and the direction (measured from positive x- axis) of the three forces actin...

Q: simply supported wood beam AB with span length L = 4 m carries a trapezoidal distributed load (see F...

A: Given data in question Loading Span member length Cross section dimensions To find out Bending s...

Q: A submersible pump is pumping water from a well that is 200 ft of water through a 4 inch PVC pipe. T...

A: Given data, Height (H1) = 200 ft Height (H2) = 50 ft Horizontal length (L) = 2000 ft Head loss due ...

Q: What volume at STP is produced when a current of 20 A is passed through a molten NacI (I) for 2.0 ho...

Q: A submersible pump is pumping water from a well that is 200 ft of water through a 4 inch PVC pipe. T...

Q: Q/Discuss the statement Why are there three types of failure in the compressive test of concrete? 2 ...

A: Workability, air content, and maturity are all routine standard testing for new concrete. The most p...

Q: Assume you are an observer standing at a point along a three-lane roadway. AlIl vehicles in lane 1 a...

Q: Calculate the ultimate axial load capacity of spiral column having a diameter of 500mm is reinforced...

A: The axial load ratio is defined as the applied axial load over the design axial load carrying capaci...

Q: evations were obtained using 10m squares. PointA ner of the lot and D-4 at the southeast corner. A

A: The scale utilized is 6m = 10m . The line is displayed underneath. The cycle used to line a line is ...

Q: 1. A parcel of land (PSU-04-24600) as surveyed for Vicente Ramos, situated in the Bgy of Pansol, Mun...

Q: Determine the maximum stress in the beam's cross section. Take M = 56 lb ft (Eigure 1) Express your ...

A: Iz=bd312=46312=72in4Iy=64312=32in4My=56sin30=28lb-ftMz=56cos30=48.4974lb-ft

Q: From the Figure, determine the minimum length of the curve. Assume a=11.2 ft/sec and perception-reac...

A: Valley curve is given with the above data and it has been asked to determine the minimum length of v...

Q: The power output of a water turbine is given by P = ρgQhwhereP = ...

A: What is the appropriate unit for P?

Q: Mr. Jae Yeong wants to put up a plant rack for his mini garden using a recyclable material from neig...

A: Find the shear and normal stress acting on the plane of weld. Then using the limiting values the val...

Question

24. Given in the accompanying sketch are the observed forward and back bearings of an open compass traverse, the adjusted forward bearing of line BC is?
25. In question 24, the adjusted back bearing of line BF is?

24. Given in the accompanying sketch are the observed forward and back bearings of an
open compass traverse, the adjusted forward bęaring of line BC is?
75 25
64°00')
20 63 50'
39 0'
01.6E91.0
D
25. In question 24, the adjusted back bearing of line BF is?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Given the closed traverse data. Lines Bearing Distance AB N20o E 20.35 BC N68oE 18.75 CD S22oE 21.30 DE S40oW 13.35 EF S62oW 9.23 FA Compute the following. Compute the bearing and distance of line FA Compute the area of the given traverse
Closed traverse ABCD has the following bearings: AB = N 45°20′ E; BC = S 47°32′ E; CD = S 14°55′W; DA =N68°00′W Compute the interior angles and provide a geometric check for your work. Find the following interior angles A, B, C, D
to find out the included angles in a closed survey PQRSTP, the following observations were made with the compass. calculate the included angles after correcting the local attractions line fore bearing(FB) back bearing(BB) PQ N 620 45/E S 62015/W QR N 210 00/W S 200 45/E RS N 710 30/W S 710 30/E ST S 390 00/W N 380 00/E TP S 540 30/E N 530 15/E
A Surveyor has Surveyed a line (Open Traverse) and Recorded the following results, the length and deflection angle of each line: AB= 30m, BC= 50m, CD= 25m , DE= 30m RBab= N 60 E, B= 30 Right, C= 45 Left, D= 30 Left. A- Draw the line using scale 1/1000. B- Calculate the angles to the right in this line
Given the following data of a closed traverse. Compute the bearing of line DE a. N 56°55’ W b. N 56°55’ E c. N 46°55’ W d. N 52°55’ E
: The following offsets were taken from a chain line to a hedge at a regular interval of 20 m from d1-d4 and at a regular interval of 300 m from d4-d8.Distance(m) d1 d2 d3 d4 d5 d6 d7 d8 Offsets (m) 3.76 4.32 5.44 4.88 3.84 3.36 3.00 2.52Determine the area in sq. meter included between the chain line, the hedge and the end offsets By Simpson’s rule. By Trapezoidal rule By Overage Ordinate rule
From the given traverse result: Lines Bearing Distance AB S35o30’W 44.37m BC N57o15’W 137.84m CD N1o45’W 12.83m DE ? 64.86m EA ? 106.72m Compute the following: The bearing of line DE The bearing of line EA Compute the area of the lot in acres.
Elementary Surveying: Measurement of Horizontal Distances, show proper and right solution. 1. A line AC cannot be measured directly because of an obstruction on theline. Accordingly, the two lines AB and BC were measured as 2,357.90mand 1,846.00m, respectively. Point B was set at a perpendicular distanceof 225m from point D on line AC. Using the approximate slope correctionformula for steep slopes, determine the length of line AC. Illustrate.
: Determine the graph and conversion of the following angles.1. Convert the following azimuth 190º15.40'45” to heading.2. Graphic 66º7´9”3. Convert the following heading S 74º9'30” W to azimuth.4. Convert the following azimuth 200º46´7.12” to heading.5. Graph 245º52´14”
1. Given the two angles of a triangular lot mark as ABC (plotted clock wise). Angles A and B are both 22o35’. Sides BC and CA are both 45.55m. a) Compute the area of the lot. b) Determine the length of side AB. c) Determine the bearing of side BC if the bearing of side AB is Due West 2. The bearing of Line BC is N 23o45’ W. If the next line CD deflect to the right by 25o34’, determine the bearing of Line CD. 3. The x and y coordinates of a point P is (- 5, 8). Convert this to polar coordinates.
Given the bearing of line AB, and the deflection angles of BC, CD, DE and EF. These lines are portion of a perimeter of a tract of land. The bearing of line AB is N 30o10’ E. LINE DEFLECTION ANGLE BC 25o to the right CD 75o to the right DE 85o to the left EF 30o to the left Compute the bearing of line BC Determine bearing of line CD Calculate the bearing of line DE Find the bearing of line EF
Measurement of three horizontal angles about point P: are APB= 12°31'50'' BPC= 37°29'20'', and CPD= 47°36'30''. If the measurement of the single angle APD is 97°37'00'', determine the most probable values of the angles.