S.1) Shown below by scanning container formed with cylinders of the shape and dimensions. S.G.-3.6, 10.8 and 14,4 there are four different liquids. Accordingly, under I atm pressure, a) Calculate the absolute pressure at points A,B,C and point D located at the bottom of the vessel b) P s? c) Rising in the thin manometer tube located next to container h-?

S.1) Shown below by scanning container formed with cylinders of the shape and dimensions. S.G.-3.6, 10.8 and 14,4 there are four different liquids. Accordingly, under I atm pressure, a) Calculate the absolute pressure at points A,B,C and point D located at the bottom of the vessel b) P s? c) Rising in the thin manometer tube located next to container h-?

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 19P: Bourdon-type pressure gauges are used in thousands of applications. A deadweight tester is a device...

See similar textbooks

Similar questions

Bourdon-type pressure gauges are used in thousands of applications. A deadweight tester is a device that is used to calibrate pressure gauges. Investigate the operation of a deadweight pressure tester. Write a brief report to discuss your findings.
In the figure below, pipe A contains gasoline (S.G.=0.75), pipe B contains oil (S.G.=0.91) and the manometer fluid is mercury (S.G.=13.6). The initial differential reading is 0.30m as shown. Determine the pressure difference between A and B.
A pressure gauge at elevation 6.5 meters at the side of a tank containing a liquidreads 95 kpa. Another gauge at elevation 2.5 meters reads 115 kpa. Compute thespecific weight of the liquid in kn/m3 and draw the figure..
PROBLEM 1: Both a gage and a manometer are attached to a tank to measure pressure. Given the reading on the pressure gage, determine the differential height h of the mercury column.
A closed pressurized tank shown below is filled with oil and mercury. Mercury is confined inan internal reservoir inside the closed tank, the height of mercury is 450mm. An openmanometer is placed on the bottom left part of the tank with liquid “X” as its gage liquid , thedeflection from the gage liquid shows 800mm. Determine the following:a) Height of the oil from point A up to point c if height A to C is 5 times the height of y.b) Pressure at point B in kPa. c) Pressure at point C in psi.
A 6 - in . - diameter piston is located within a cylinder which is connected to a 4 - in . - diameter inclined - tube manometer as shown in Fig . P2.53 . The fluid in the cylinder and the ma nometer is oil ( specific weight = 59 lb / ft ? ) . When a weight W is placed on the top of the cylinder the fluid level in the ma nometer tube rises from point ( 1 ) to ( 2 ) . How heavy is the weight ? Assume that the change in position of the piston is negligible .
6.60 Gasoline (sg = 0.67) is flowing at 0.11 m3/s in the fabricated tube shown in Fig. 6.19. If the pressure before the contraction is 415 kPa, calculate the pressure in the smaller tube.
An open tube is attached to a tank as shown. A). If Liquid X (Oil SG=0.55) rises to a height of 800 mm in the tube, what is the pressure Pa (in kPa) of the air above water? Neglect capillary effects in the tube. B). If Liquid X (Alcohol SG=0.79) rises to a height of 800 mm in the tube, what is the pressure Pb (in kPa) of the air above water? Neglect capillary effects in the tube.
The cylindrical tank with hemispherical ends shown contains a volatile liquid and its vapor. the liquid density is 0.87 and its vapor density is negligible. The pressure in the vapor is 119 kPa (abs), and the atmospheric pressure is 101 kPa (abs). (a.) Determine the gage pressure reading on the pressure gage in kPa. (b.) Determine hte height, h, of the mercury manometer in centimeters.
A time independent non Newtonian fluid of density 0,00085kg/cm3 flows in a cylindrical pipe with a mean linear velocity of 1.70 m/s at steady state. The pipe is 3m long with an inside diameter of 0.075m. The point pipe consistency coefficient is 1.52 (N/m2)s0.3 and the flow behavior index is 0.3. Determine: a) The point values of the apparent viscosity. b) Reynolds Number. c) Pressure drop in Pascals.
Water flows steadily from a nozzle into a large tank as shown below. The water then flows from the tank as a jet of diameter d. (a) Using the piezometer tube shown, determine the flow rate through the nozzle. (b) Using the flow rate determine the value d if the water in the tank remains constant. Viscous effects are negligible.
1) A glass manometer with oil as the working fluid is connected to an air duct. Which of the following picture is CORRECT? a or b 2) A device measured stagnation pressure is called? a) barometer b) Piezometer c) Pitot tube d) manometer