SAE 10W30 oil flows from one tank to another when the gate valve is fully opened as shown in the following figure. The pipe is made of commercial steel and has a diameter of 20 mm. Calculate the total losses (in m) through the pipes. Include minor losses due to the flush entrance (K₁ = 0.5), fully opened gate valve (K₁ = 0.5), and two 90° elbows (K₁ = 0.9). Take po = 920 kg/m³ and v = 0.1(10-3) m²/s and Q = 0.0007 m³/s. Note: The answer should be in decimal values with two decimal places 5 m A 2 m 6 m 1 m B

SAE 10W30 oil flows from one tank to another when the gate valve is fully opened as shown in the following figure. The pipe is made of commercial steel and has a diameter of 20 mm. Calculate the total losses (in m) through the pipes. Include minor losses due to the flush entrance (K₁ = 0.5), fully opened gate valve (K₁ = 0.5), and two 90° elbows (K₁ = 0.9). Take po = 920 kg/m³ and v = 0.1(10-3) m²/s and Q = 0.0007 m³/s. Note: The answer should be in decimal values with two decimal places 5 m A 2 m 6 m 1 m B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Oil with sp. gr. 0.95 flows at 200 lit/sec through a 500 m of 200 mm diameter pipe (? = 0.0225). Determine (a) the head loss (m) and (b) the pressure drop (kPa) if the pipe slopes down at 10⁰ in the direction of flow.
Question 1 a) List out 3 devices to measure hydrostatic pressure. Explain how U-tube manometer can be used to measure hydrostatic pressure in the pipe. P1N P1 h, A Flow Test Section U-Tube Differential Manometer
A valve is suddenly closed in 200 mm diameter pipe. The increase in pressure is 700 kPa. Assuming that the pipe is rigid and the bulk modulus of water is 2.07 x10° Compute the maximum discharge.
ubject Date No. The water mercury manometer of Frgure shown Indicates a differential reading of o.30m when the pressure in pipe A is 0,30m 30 Hg vacuuem Determine mm the pressure in pipe B in Kpa ? tmercury
Q2: An otl of viscosity Co.15 pas) and specific gravity 0.9 is flows Throngh 1.Find The slope of The Pipe That will canse The Pressure to be constantalong The pipes entire length? an inclined (300mm) diameter Pipe. Q= 0.005m3/sec 3oomm Dia. Zz datum 2. check if The Rlow is laminarRlow?
4. The figure shows two cylinders of diameter D and 2D, connected to each other and containing an incompressible fluid. The two cylinders are filled with leak-proof pistons of weight W1 and W2 as shown. The releationship between W1 and W2 is a) W2 = W1 b) W2 = 0.5 W1 c) W2 = 5 W1 d) W2 = 0.4 W1 20 k- 5. A flat plate is sliding at aconstant velocity of 5 m/s on a large horizontal table. A thin layer of oil ( of absolute viscosity 0.4 N.s/m2) separates the plate from the table. To limit the shear stress in the oil layer to 1 kpa, the thickness of the oil film (mm) should be most nearly to a) 0.2 b) 20 c) 1.6 d) 1.85
pipe 310 m Water is flowing in a straight concrete lining centrifugally spun pipe as shown in the figure problem 12. The difference between the two gauge readings is 185 kPa. The flow rate is designed to be 30 liter/s. By using Darcy Weisbach and Hazen William's formula, determine the pipe diameter. (Ans.: 228 mm, 123 mm) TABLE 5.1: Pipe Characteristies Pipe Hazen-William* Roughness e (mm) 0.15 C 140 Asbestos Cement (AC) – all ages Cast Iron, Ductile Iron - new 0.3 130 10 years old - 20 years old 1.5 3.0 100 90 Cast Iron coated – good condition all ages Welded steel - uncoated - new 0.3 135 125 100 100 - old 0.6 1.5 Coal tar enamel coated steel – new Concrete lining centrifugal spun – all ages Galvanized Iron (GI), Mild Steel (MS) HDPE, UPVC, Polyethylene Wrought Iron Copper, Brass *The Malaysian Water Association - MWA (Design Guidelines for Water Supply Systems) 0.15 0.15 140 0.3 130 0.015 155 0.045 ND 0.0015 ND ND = No Data
2- Oil (p = 80o kg/m2) flow through a 5omm-diameter smooth pipe at a velocity of 2m/s, the pressure drop due to friction loss in the pipe 5023 pa. The pipe length is 1om. a- Calculate the friction factor, f. %3D b- Determine whether the flow is laminar or turbulent. C- Calculate the oil viscosity. (b) o.0157 (d) 487x10-6 N s/m2]
Question 7 A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 120 (Hazen-Williams) Pipe 2 n = 0.020 (Chezy-Manning) Pipe 3 f = 0.025 (Darcy-Weisbach) All pipes have a diameter of 400mm, length of 1 kilometer, and flow rate of 150 L/s. Determine the headloss on Pipe 3 in meters.
Oil of SG 0.75 flows through the nozzle shown and deflects the mercury in the U-tube gage. What is the pressure at B in Kpa? A 2.75 D h B C Hg(13.6)
Part 2Two pipes are connected by a manometer as shown. Determine the pressure difference, between the pipes in kPa.
The pipe is 25mm with friction factor of 0.022. The second tank is vented. H1=1.4m H2=4.5m H3=1.0m X1=14.9m X2=2.7m Calculate the pressure(kPa) above the gasoline in the first tank that will result in a flowrate of 400 liters/min.