Seepage takes place around a retaining wall shown in Figure Q5c. The coefficient of permeability, K of the sand is k x10-³ cm/s. Where k is the last digit of your student identity number. If the retaining wall is 30m long, calculate the quantity of seepage across the entire wall per day. Take k = 2, if the last digit of your student identity number is zero (0).

Seepage takes place around a retaining wall shown in Figure Q5c. The coefficient of permeability, K of the sand is k x10-³ cm/s. Where k is the last digit of your student identity number. If the retaining wall is 30m long, calculate the quantity of seepage across the entire wall per day. Take k = 2, if the last digit of your student identity number is zero (0).

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter2: Geotechnical Properties Of Soil

Section: Chapter Questions

Problem 2.9P

See similar textbooks

Similar questions

The diagram of a sand drain is shown in Figures 16.21 and 16.22. Given: rw = 0.25 m, rs = 0.35 m, de = 4.5 m, Cv = Cvr = 0.3 m2/month, kh/ks = 2, and Hc = 9 m.Determine:a. The degree of consolidation for the clay layer caused only by the sand drains after six months of surcharge applicationb. The degree of consolidation for the clay layer that is caused by the combination of vertical drainage (drained on top and bottom) and radial drainage after six months of the application of surcharge. Assume that the surcharge is applied instantaneously.
4. With two cases shown in the following figure: Plot pore pressure with depth for the soils if hydraulic conductivity of soils K1 = 5 x K2. a- b- flow through a unit thickness of the cross-section if K1 = 5 x 10$ (f/s) and K2 = 1 x 10$ (f/s). Estimate the rate of seepage (q) per linear foot of cross-section, i.e. calculate the rate of C- Plot flow net for 2 cases. -z (ft) z (ft) Water Water 3 ft 3 ft Soil 1 1.5 ft Soll 1 Sol 2 3 ft 3 ft 3 ft 1.5 ft Soil 2 Datum psf Datum psf porous stone porous stone 3 ft 1.5 ft 1.5 ft Case 1 Case 2
A sand has Gs = 2.66. Calculate the hydraulic gradient that will cause boiling for e = 0.35, 0.45, 0.55, 0.7, and 0.8.
The section through a long cofferdam is shown below, the coefficient of permeability of the soil being 6x10-8 m/s. Determine the quantity of seepage entering the cofferdam. 5.50 m 0 1 2 3 4 5 1 As = 0.70 ml B to 10 15 m
2. Estimate the hydraulic conductivity (in cm/sec) of a poorly graded sand with the following characteristics: d100 = 0.425mm, d50= 0.3mm, d30 = 0.25mm, d10= 0.2mm, and do = 0.1mm. Show your work and circle your answer.
For the figure shown below, if the area of the tank is 0.5 m² and hydraulic conductivity of sand is 0.1 cm/sec. a. What is the magnitude and direction of the rate of seepage? b. If the value of h=1.2m, will boiling occur? Why? c. What should be the value of "h" to cause boiling? Outflow Inflow 1m 2m A B h = 1.2m e = 0.55 G=2.68 Valve (open)
5. The coefficient of permeability of a sand at a void ratio of 0.62 is 0.03 cm/sec. Estimate the coefficient of permeability at a void ratio of 0.48. Using Casagandre equation Using Kozeny-Carman equation Find the difference in the rate of flow using the results of “a” and “b” if i = 0.70 and A = 0.6 m2.
i. A sandstone core sample is saturated 100% with water. Calculate the absolute permeability of the core sample if the water is flowing at 6.21 cubic centimetres per second. The length of the core sample is 14 centimetres and its diameters is 6 centimetres. The pressure differential across the core sample is 15 atmospheric pressure and the water viscosity is 1.2 centipoises. Explain a method of how the permeability of low permeability reservoirs can be ii. improved.
1. For a constant head laboratory permeability test on a fine sand, the following values are given: L = 300 mm; D₁ = 200 mm; h = 400 mm; Vol = 420 m³; t = 4 min; e = 0.55. a. Compute the coefficient of permeability in cm/sec. b. Compute the discharge velocity in cm/sec. c. Compute the velocity. seepage 2. For a falling head permeability test, the following are given. Length of specimen is 380 mm, are of specimen - 6.5 cm², hydraulic conductivity of soil specimen is 0.175 cm/min. a. What should be the area of the stand pipe for the head to drop from 650 cm to 300 cm in 8 min?
Situation 1 – Refer to the picture. 1. Assume 3K1=K2=1.5K3=2K4 K1=3.5x10-2 (cm/s) Calculate the equivalent coefficient of permeability. 2. Assume 3K1=K2=1.5K3=2K4 K1=3.5x10-2 (cm/s) Calculate the rate of seepage 3. Assume 3K1=K2=1.5K3=2K4 K1=3.5x10-2 (cm/s) Calculate the height of water above C if piezometer was placed at that point
glass container with pervious bottom containing fine sand in loose state (void ratio 0.8) is subjected to hydrostatic pressure from underneath until quick condition occurs in the sand. If the specific gravity of sand particles -2.65, area of cross-section of sand sample 10 cm² and height of sample = 10 cm, compute the head of water required to cause quicksand condition and also the seepage force acting from below. Seepag
2. Consider the stratified soil deposit shown in the figure. There are four layers, 3m thick each, and kH1=2x10³, kH2=1x105, kµ3=2x104, kH4=1x10³in cm/sec. Determine the equivalent coefficient of permeability in the horizontal direction and the total flow in cm3/sec per cm width. H Direction of flow