Select only Three(3) Difference between UTP Cable and Fiber-optic. A. UTP Highly immune to EMI and RFI than Fiber-Optic. B. UTP has lower to immunity to electrical hazard than Fiber-Optic C. Fiber-Optic required a highest installation skills to install D. Highest connector and media cost for Fiber-Optic than UTP E. Fiber-Optic bandwidth can reach to 1000Gb/s

Select only Three(3) Difference between UTP Cable and Fiber-optic. A. UTP Highly immune to EMI and RFI than Fiber-Optic. B. UTP has lower to immunity to electrical hazard than Fiber-Optic C. Fiber-Optic required a highest installation skills to install D. Highest connector and media cost for Fiber-Optic than UTP E. Fiber-Optic bandwidth can reach to 1000Gb/s

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 7RQ

See similar textbooks

Similar questions

15.a. Who is responsible for maintaining and repairing lightwave equipment in a dark fiber lease?A. CarrierB. LessorC. Both lessor and lesseeD. Lessee15.b. What should the PMD value be in a 10 Gbps fiber link?A. Exactly 10 psB. Less than 7 psC. Greater than 7 psD. Exactly 7 ps
6. Which type of fiber is used in a standard FDDI network?A. OM3 or OM4 at 850 nmB. OM1 at 1,550 nmC. OM2 at 1,310 nmD. OM1 at 1,310 nm
A simple point-to-point microwave transmission link has no redundancy. Failure of the link will result in an outage. Therefore, typical microwave transmission links are designed with redundancy. Explain the following redundancy techniques 1+1 Hot Standby (HSB), 1+1 Space Diversity (SD), and 1+1 FD.explain.
What type of fiber cable problem is caused when pairing a 50-micron core cable with a 62.5-micron core cable? a. Dirty connectors b. Wavelength mismatch c. Fiber type mismatch d. TX/RX reverse
15.a. How can a poorly attached connector affect signal strength in a fiber optic cable?A. Insertion loss can decrease.B. Return loss can decrease.C. Splice loss can increase.D. Return loss and insertion loss can increase.15.b. A certain cable has a minimum bend radius of 10 cm. If you install this cable in a straight pull box, how long should the pull box be?A. Less than 40 cmB. Exactly 25 cmC. Exactly 40 cmD. At least 40 cm
4. Please show all work! Switched virtual circuit transmission overhead could be high to send a small amount of information. Assume the distance as 4,500 km, the propagation speed as 200 meters per microsecond and OC3 payload of 150.336 Mbps with 5.184 Mbps overhead. Calculate the minimum time to transmit one ATM cell from Miami to San Francisco on a basic SONET network OC-3 for the following cases: (a) Datagram service (b) Switched virtual circuit service (c) Permanent virtual circuit service
4.a. How many STM signals are combined into a 2488.32 Mbps SDH network?A. 32,256B. 16C. 48D. 644.b. What can installation records be used to determine while servicing equipment?A. Broken connectors in a cable linkB. Problems due to aging during operationC. Broken fiberD. Decreased bending radius during operation
100. Satellite-Switched Time-Division Multiple Access (SS/TDMA) is a. a form of TDMA in which circuit switching is used to dynamically change the channel assignments b. the method of determining which device has access to the transmission medium at any time c. a medium access control technique for multiple access transmission media d. all of the above
17. When measuring fiber attenuation in DWDM or CWDM channels, which channels should be checkedfor attenuation?A. The highest wavelength channelB. No channelsC. All channelsD. The lowest wavelength channel
Identify the differences between the following communication hardware. (max of 5 lines) 1-NIC card 2-Hubs, 3-Switches 4-Routers
What fiber is used in fiber-optic cabling to protect the inner core and prevent the cable from stretching?What fiber is used in fiber-optic cabling to protect the inner core and prevent the cable from stretching?
Question 2 (a) Ethernet uses CSMA/CD as it's medium access mechanism. Can you explain how the three concepts that are used in CSMA/CD(CS, MA, and CD). CS: MA: CD: