نقطتان (2)*Select the right reading of the?Micrometer Screw Gauge00.125 mm O0.150 mm0.152 mm0.120 mm0.100 mm0tmt20أخرى:

we need to find reading in the micrometer.

Answered: Select the right reading of the…

Engineering

Mechanical Engineering

Select the right reading of the ?Micrometer Screw Gauge

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter2: Measurement, Materials, And Safety

Section2.4: Precision Measurement

Problem 13RQ: What is the smallest graduation on a metric micrometer with a vernier scale?

See similar textbooks

Related questions

Q: The mass of a spring-mass system is initially displaced by 10 cm from its unstressed position by…

A: given; initial displaced(x0)=10cm =0.1mapplying force(F)=25Nmass of…

Q: pressure begins at atmospheric pressure (sea level) as the reference, and works its way down to a…

A: Pressure is calculated using the F/A formula (Force per unit area). The Pascal is a unit of…

Q: Determine the moment of inertia with respect to the x and y axes of the area bounded by (y-1)2 =4-2x…

A: Concept: The equation of the moment of inertia about y-axis. Here, dA is the area of strip.

Q: A steady stream of air enters a horizontal compressor at the rate of 0.02 kg/s. The air temperature…

A: During a steady flow process, the total energy content of a control volume remain constant i.e.,…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: Answer: The maximum load that can be supported by the structure: P = 29.046 kN

Q: sk (1) Brayton cycle with regeneration operates with a pressure ratio of 7. The minimum and maximum…

Q: For nos. 24-37, satisfy the conditions of the given problem below: The truss is loaded as shown in…

Q: A Carnot heat engine operates between a source at 1000 K and a sink at 300 K. If the heat engine is…

Q: * = pw 2 gm/cm³ O 1 gm/cm³ O 4 gm/cm³ O 3 gm/cm³ O 5 gm/cm³ O

A: Given:- Density of water = ................. g/cm3 Options Provided:- 2 1 4 3 5

Q: Q1:Put the true or false in the statements following. 1-Density is measuring in (m/kg). 2-Mass flow…

Q: Q2: Choose the correct letter that represents the correct answer and choose ten only. 1- Minor…

A: When the fluid flow takes place through the pipe, then there is loss of head. These losses are…

Q: Symmetrical objects can be effectively shown using a Select one: O A. Half O B. Quarter O C. Full…

Q: 1. A Carnot engine operates at a temperature between TH = 850 K and TL = 300 K. The engine produces…

Q: A 173-lb snowboarder has speed v = 15 ft/sec when in the position shown on the halfpipe. Determine…

Q: Question 14 The total amount that the feature on the actual part is allowed to vary from the…

Q: Which of these methods cannot be used to create parts in solid modelling Select one: O A. Rotation…

A: Correct answer: (E) Expansion

Q: * A Carnot heat engine operates between a source at 1000 K and a sink at 300 K. If the heat engine…

Q: The two springs are identical, with unstretched length 0.4 m. When the 150-kg mass is suspended at…

Q: Q3:A small truck has #cylinder ,4 liter compression ignition engine that operates on ir standard…

Q: Q3: Air flows across a 20-cm-square plate with a velocity of 5 m/s. Free-stream conditions are 10°C…

Q: 12mm 012122LM12(P1.75)"16L 122mm/4.8in Thread pitch:1.75mm 1.75mm M12*1.75 16mm

Q: 2/162 Replace the two forces and one couple acting on the rigid pipe frame by their equivalent…

Q: * When a mass of 1.2 kg is Applied on Piston area of 324 mm2. That means the pressure value equal to…

A: Given : mass, m =1.2 kg area, A = 324 mm2 To find : Pressure

Q: For the Rankine cycle shown below, Determine the power output from the turbine? Steam 40 bar, 350 °C…

Q: 9---------- is a example of Interstitial Solid Solutions. Ge Si Cu Ni O Fe C 10- Ceramics are mostly…

A: 9. Interstitial solid solution is defined as the solution in which solute atom occupies the…

Q: erature is 32 ASSUMPTIC

A: Given: m= 5 kg T1 =1500 C T2 = 3200 C

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

Q: What is the number of degrees of ?freedom for the system ma k₂ m₂ lo 5DF O 2DF O 3DF O SDF

Q: costs Tom and Jerry are each trying to sell you a heat engine. Both engines work between high and…

Q: he eccentricity of a conic section is 5/7. Which conic section is this? elect one: O A. Circle O B.…

Q: Express and identify the resultant of the two forces and one couple shown acting on the shaft angled…

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 13 kN applied at A. Assume a…

Q: An object moving with speed of 5 m/s has kinetic energy of 1200 J. Find the mass of object

A: Given data : Kinetic energy (K.E)=1200 J Velocity (V)=5 m/s Required : Mass of object

Q: The figure (Figure 1) shows five metal plates, all at the same temperature and all made from the…

Q: Q4: Water at the rate of 0.8 kg/s is heated from 35 to 40°C in a 2.5-cm-diameter tube whose surface…

Q: Locate the centroid (x, y) of the shaded area. 12 3.5 6.5 (Dimensions in mm)

A: To find: The x and y coordinates of the centroid of the given section.

Q: The composite beam is made of steel (A) bonded to brass (B) and has the cross section shown in…

Q: Not all engineering systems can be represented as a DOF when vibration analysis is required Ture O…

Q: Find the temperature of a rod 0 < x < 1 thermally insulated along the surface, if heat sources of…

Q: Bar (1) has a cross-sectional area of 0.75 in.². If the stress in bar (1) must be limited to 39 ksi,…

A: Correct answer: (b) 17.55 kips

Q: X₁ Lt) H X₂ ( t) ¾k₁ = k m₁ =m 2k₁=k M₂=M { K3=2K The spring constants are K₁=k, K₂=3k, K₂=2k find…

Q: In Fig. 3, determine the smallest vertical force P required to push the wedge between the two…

Q: As a part of preliminary design study, the effects of wind loads on a 275 m high building are…

Q: Use the virtual work method to determine the vertical deflection at joint C of the frame shown. 30…

A: Given data: EI= constant Modulus of elasticity (E)=200 GPa Moment of inertia (I)=8000×106 mm4

Q: The initially stationary 24-kg block is subjected to the time-varying force whose magnitude P is…

Q: Locate the centroid (x, y) of the shaded area. y 2 3.5 12 6.5 3 3 x

A: To find: The x coordinate of centroid, x = ? The y coordinate of centroid, y = ?

Q: Choose the correct answer : 1. What are the factors that affect the volumetric efficiency? a.…

A: 1.

Q: 3.) A steam power plant uses the ideal Reheat-Regenerative Rankine cycle where the steam enters the…

Q: The assembly shown in Figure 3 is subjected to a vertical shear of V = 35 kN. Determine the shear…

Q: Question: Sketch the greaphs of T and T2

A: The given question is not clear about which topic. Assumed, the graphs required related to…

Question

نقطتان (2)
*
Select the right reading of the
?Micrometer Screw Gauge
0
0.125 mm O
0.150 mm
0.152 mm
0.120 mm
0.100 mm
0
tmt
20
أخرى:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A GO/NO-GO snap gage is required to inspect the diameter of a shaft that is 1.000 ± 0.020. A wear allowance of 2% of the entire tolerance band is applied to the GO side. Determine (a) the nominal sizes of (a) the GO gage and (b) the NO-GO gage
Question 1(a)Given the measured value is 20.04mm and the true value of the measured dimensionis +-(plus minus) 20.02. Calculate the percentage of errors on this dimension.(b)Some errors in the measurement can be avoided. List 3 of the avoidable errors inmeasuring of component.(c)Named the 4 classifications of the Tolerance and briefly explain each of it.
Note: The number of significant digits is set to 3. The tolerance is +/- 1 in the 3rd significant digit Subject: statics of rigid bodies// mechanical engineering
List and briefly describe the three types of tolerances used on prints.
What is the smallest graduation on a metric micrometer with a vernier scale?
For the following statements, answer True or False and explain the answer briefly. The tolerance of standard mass used must be smaller than the uncertainty of analytical balance to be calibrated.
Determine the limits of sizes, tolerances and fundamental deviations for the shaft designated as 40 H8 / f7
A ruler used to measure a penny has markings every 1 mm. Which for the size of the penny is correctly reported for this ruler? a. 19.05 mm b. 19 mm c. 19.1 mm
Tolerances for a hole and shaft assembly having a nominal size of 50 mm are as follows: Hole = 50 (+0.02 )/(+0.00 ) mm and Shaft = 50 (-0.05)/(-0.08) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.
Some hole size tolerances are specified as D7, N6, and H8. Where does the print reader find the values for those specifications? (Multiple Choice)a. In a tolerance block located in the upper-left corner of the sheetb. On line at the manufacturers websitec. A supplemental documentd. The are proprietary and not stated
(USCS UNITS) A GO/NO GO PLUG GAUGE WILL BE DESIGNED TO INSPECT A 2.000 +/- 0.002mm DIAMETER HOLE. A WEAR ALLOWANCE OF 5% OF THE TOTAL TOLERANCE BAND IS APPLIED TO THE GO SIDE OF THE GAUGE. DETERMINE THE NOMINAL SIZES OF THE GO GAUGE. ROUND YOUR ANSWER TO THE NEAREST TENTH OF A THOUSANDTH OF AN INCH
A metric thread of pitch 2 mm and thread angle 60° is inspected for its pitch diameter using 3 wire method. The diameter of the best size wire in mm is, (a) 0.866 (b) 1.000 (c) 1.154 (d) 2.000