Sheet 4Exercise 1:The buck de-dc converter of Fig. 1 a has the following parameters:VL+iRicV.VxFigure 1V, = 50 VD = 0.4L= 400 μΗC = 100 µFf = 20 kHzR = 20 NAssuming ideal components, calculate (a) the output voltage Vo, ( b) the maximum andminimum inductor current, and (c) the output voltage ripple.

Answered: Image /qna-images/answer/267aabed-41ed-45eb-abdb-1c4620784076.jpg

Sheet 4 Exercise 1: The buck de-de converter of Fig. 1 a has the following parameters: VL ell iR ic Vs Figure 1 V, = 50 V D = 0.4 L = 400 µH C = 100 µF f = 20 kHz R = 20 N Assuming ideal components, calculate (a) the output voltage Vo, ( b) the maximum and minimum inductor current, and (c) the output voltage ripple.

Sheet 4 Exercise 1: The buck de-de converter of Fig. 1 a has the following parameters: VL ell iR ic Vs Figure 1 V, = 50 V D = 0.4 L = 400 µH C = 100 µF f = 20 kHz R = 20 N Assuming ideal components, calculate (a) the output voltage Vo, ( b) the maximum and minimum inductor current, and (c) the output voltage ripple.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

an 8-bit analog-to-digital converter, with an input range of 0 to 10 V, was used in conjunction with a load cell, whose output varies linearly between 0 and 5 V for a load range between 0 and 1000 N. What is the approximate resolution of this system? a) 5.32 Nb) 7.84 Nc) 8.15 Nd) 10.00 Ne) 25.00 N
What is the voltage gain of the instrumentation amplifier as shown if R1 = 1.5 kΩ, R2 = 75 kΩ, R3 = 10 kΩ, and R4 = 10 kΩ. What is the outputvoltage if υ1 = (2 + 0.1 sin 2000πt) V and υ2 = 2.1 V?
(a) Draw the AC equivalent circuit for the circuit given in Fig. 4.(b) Calculate the overall/total voltage gain AVTL and output voltage V0 for the circuit in Fig. 4. You are required to show all necessary steps for your calculations.
Find the saturation current (ICsat) for the fixed-bias configuration of Fig. 4.118 .
Qa4 Sketch the output voltage (V) for the circuit and the input voltage (V) shown in figure (3). Di[Va=6.4V, 8| DaVar-16.6V, Gdl Fig 3
(a) Design an astable multivibrator to oscillate at a frequency of 1 kHz. Use the circuit in Fig. 12.62 with symmetric supplies of ±5 V. Assume that the total current from the op amp output must never exceed 1 mA. (b) If the resistors have ±5 percent tolerances and the capacitors have ±10 percent tolerances, what are the worst-case values of oscillation frequency? (c) If the power supplies are actually +4.75 and −5.25 V, what is the oscillation frequency for the nominal resistor and capacitor design values?
VC=9 V, Rin=1.1 kΩ, RB1=170 kΩ, RB2=110 kΩ, RC=5.3 kΩ, RE=3.6 kΩ Calculate the voltage gain Vout/Vin (VBE=0.7V, VT = 25 mV, β = 200).
4.68 Using the exponential diode characteristic, show thatfor vS and vO both greater than zero, the circuit of Fig. 4.23(a)has the transfer characteristicvO= vS−vDat iD=1 mA−VT lnvO/Rwhere vS and vO are in volts and R is in kilohms. Note thatthis relationship can be used to obtain the voltage transfercharacteristic vO vs. vS by finding vS corresponding to variousvalues of vO.
Q24.In the circuit shown in Fig. 23, the operating point is chosen such that IC = 2mA, VCE = 3V. If RC = 2.2 kΩ, VCC = 9V and β = 50, determine the values of R1, R2 and RE. Take VBE = 0.3V and I1 = 10 IB .
If in the circuit of Example 5.5 the value of R, is doubled (to 13.1 k52), find approximate values for I, and V» Ans. 0.15 mA: 0.05 V Need work
A piezoelectric system having 500mV output for pressure measurement, design an inverting amplifier for 2V to display the pressure in the display unit. a. R2 = 0.5R1 b. R2 = 5R1 c. R2 = R1 d. R2 = 10R1
ngineering Electrical Engineering Q&A Library A students working on amplifier having input voltage is 2.5 mV, Input resistance is 2 Killo ohm and feedback resistance is 200 killo ohm then solve following 1. Evaluate the gain for non inverting amplifier. 2. Calculate gain of the current. 3. Evaluate the output voltage. 4. If input voltage is applied to non inverting terminal then calculate the output voltage. 5. Analyze the nature of output voltage. A students working on amplifier having input voltage is 2.5 mV, Input resistance is 2 Killo ohm and feedback resistance is 200 killo ohm then solve following 1. Evaluate the gain for non inverting amplifier. 2. Calculate gain of the current. 3. Evaluate the output voltage. 4. If input voltage is applied to non inverting terminal then calculate the output voltage. 5. Analyze the nature of output voltage. Question A students working on amplifier having input voltage is 2.5 mV, Input resistance is 2 Killo ohm and feedback resistance is 200…