Short Problem: From a sinusoidal waveform derived from an oscilloscope, determine the form factor in decimal given the following data (hypothetically): Oscilloscope Setting: Time per division: 2.255 sec/div Volts per division: 4.764 V/div Probe Setting: x1 Waveform Reading: Vertical no. of divisions (Peak Value): 5.7 division Horizontal no. of divisions (one cycle): 6.4 division Note: Follow this reminder carefully. Compute to the nearest 2 decimal places (no scientific notations) Do not round off in the middle of calculation. Use stored values. Write the numerical values only. No units in your final answer. Spaces are not allowed. Excessive number of decimals as compared to the required number of decimals may result to an incorrect answer. Use Veff=(1/sq. root of 2)Vm

Short Problem: From a sinusoidal waveform derived from an oscilloscope, determine the form factor in decimal given the following data (hypothetically): Oscilloscope Setting: Time per division: 2.255 sec/div Volts per division: 4.764 V/div Probe Setting: x1 Waveform Reading: Vertical no. of divisions (Peak Value): 5.7 division Horizontal no. of divisions (one cycle): 6.4 division Note: Follow this reminder carefully. Compute to the nearest 2 decimal places (no scientific notations) Do not round off in the middle of calculation. Use stored values. Write the numerical values only. No units in your final answer. Spaces are not allowed. Excessive number of decimals as compared to the required number of decimals may result to an incorrect answer. Use Veff=(1/sq. root of 2)Vm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. What effect does changing the frequency on the effective value of sinusoidal voltage? 2. What effect does changing the amplitude on the effective value of sinusoidal voltage?
A sinusoidal voltage trace displayed by an oscilloscope is shown, if the 'time/div' or Hs, switch is set to 0.2 us/div and the 'volts/div' Vs, switch is set to 50 mV/div, from the waveform, the frequency and the maximum voltage of the sinusoid is
1. With a neat sketch briefly explain how an alternating voltage is produced when a coil is rotated in a magneticfield. 2. Derive expressions for average value and RMS value of a sinusoidally varying AC voltage 3. A circuit having a resistance of 12Ω, an inductance of 0.15 H and a capacitance of 100μf in series is connectedacross a 100V, 50Hz supply. Calculate the impedance, current, the phase difference between the current andsupply voltage. 4. Two circuits with impedances of Z1 = 10 + j15Ω and Z2 = 6 – j8Ω are connected in parallel. If the supply current is 20A, what is the power dissipated in each branch?
The current in a pure capacitor circuit is i=0.17cos500t. If the rms value of the impressed emf is 80 volts. a) What are the equation for the voltage and power? b) What is the circuit frequency?
b) Determine the voltage ?(?) and current ?(?) sinusoidal forms. Sketch one cycle of the waveforms in the same x-axis. Clearly indicating the peak value and the period of each waveform and the phase difference (in milliseconds) between the two waveforms. c) Determine the values of resistance R and inductance L. d) Determine the phasors ?L, ?r and ?c. e) Sketch the phasor diagram showing ?s, ?r, ?r, ?c and ?.
Determine the RMS values of each waveform below: (full-wave sinusoids, square-wave, sawtooth, and triangle) Please all subpart is compulsory please Please in typing format Please all subpart is compulsory in short explanation
a) Explain why root mean square (RMS) is used to quantify the strength of an AC signal. b) If SI units are Meter (m), Kilogram (kg), Second (s), Ampere (A), Kelvin (K), Mole (M) and Candela (C), then express Voltage, Resistance, Capacitance, Inductance, Power and Energy in terms of SI units.
15. If a non-electrolytic capacitor with a maximum voltage rating of 100v is connected to an AC signal, what is the largest RMS voltage that can be used?
What is the average value, G, of this strange waveform?(need handwritten solution only please otherwise downvote).
Consider a 760 W light bulb that requires an RMS voltage 21 V to operate normally. How large should an inductance be connected in series with the bulb if the combination is connected across a RMS voltage 255 V, 71 Hz line? (You may neglect the resistance of the inductor and the inductance of the light bulb.)
-) Below are two voltage patterns measured from an oscilloscope. The voltage stage of the CHI probe is 5 V / div, the CH2 probe voltage stage is 10 V / div and the time axis is 2ms / div. According to this information, a) What are the peak to peak and rms voltage values of the voltages in CHI and CH2? b) What is the frequency of the voltages in Hz? c) How many degrees is the phase difference between the two voltages, which voltage is leading?
1. solve equation of the sinusoidal signal v(t) from the information, where v(t) = Vp sin ωt. Vp-p = 6 div Oscilloscope setting: horizontal = 0.5 ms/div 1 cycle = 8 div vertical amplitude = 0.5 volt/div 2. 1 cycle of 2 sinusoidal signals displayed with 10 kHz on the oscilloscope screen. If the two signals have a difference time with 20µs, what the value of phase shift between two signals/waveforms displayed on the scope screen? 3. It is possible for a circuit made up of a resistor, an inductor, and a capacitor (connected in series or parallel) to behave like a purely resistive circuit. Explain why.