Show complete solutions and figures A rectangular dam having a width of 14.8 m has a height of 23.2 m. The depth of the water on one side of the dam is 20.4 m. If the coefficient of friction between the dam and the foundation is 0.85, compute the factor of safety against OVERTURNING. Use unit weight of concrete equal to 2310 kg/cu.m.

Show complete solutions and figures A rectangular dam having a width of 14.8 m has a height of 23.2 m. The depth of the water on one side of the dam is 20.4 m. If the coefficient of friction between the dam and the foundation is 0.85, compute the factor of safety against OVERTURNING. Use unit weight of concrete equal to 2310 kg/cu.m.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter7: Settlement Of Shallow Foundations

Section: Chapter Questions

Problem 7.2P: A planned flexible load area (see Figure P7.2) is to be 3 m × 4.6 m and carries a uniformly...

See similar textbooks

Similar questions

A dam is triangular in cross section with the upstream face vertical. Water is flushed with the top. The dam is 9m high and 7m wide at the base and weighs 2.6 tons per cubic meter. The coefficient of friction between the base and the foundation is 0.8. a.Determine the minimum unit pressure on the foundation. b. Determine the factor of safety against sliding. c. Determine the factor of safety against overturning.
Estimate the equivalent hydraulic bearing for flow in the vertical direction. Suppose that k1= 10 x 10^-4 cm/s, k2 = 5.0 x 10^-4 cm/s, k3 = 6.0 x10^-4 cm/s, k4 =3.0 x 10^-4 cm/s, H1 = 2.5 m, H2 =1.5 m, H3 =1.0m, H4 = 2.5 m.
A dam is triangular in cross-section with the upstream face vertical. Water is flushed with the top. The dam is 8m high and 6m wide at the base and weighs 2.4 tons per cubic meter. The coefficient of friction between the base and the foundation is 0.8. Determine (a) maximum and (b) minimum unit pressure on the foundation, and factors of safety (c) against overturning and (d) against sliding.
A dam rectangular in cross – section with upstream face vertical. Water is 20.4 m deep on the upstream side. The dam is 23.2 m high and 14.8 m wide at the base and weighs 2310 kg/m3. Coefficient of friction between the base and the foundation is 0.85. Compute the factor of safety against sliding. a. 3.85 b. 2.67 c. 3.24 d. 1.45
The concrete dam of trapezoidal cross section is shown with T = 1m, B = 4.3m, H = 9m and h = 6m. The unit weight of the concrete is 24??⁄?3. For the given conditions, evaluate the resisting moment of the dam to overturning in kN.m per meter length of dam. Unit of the Correct Answer: kN-m
A masonry dam has a trapezoidal cross-section 25 m high, crest width of 3 m and base length 18 m. The upstream face slopes down 12 m in 25 m and the downstream faces slopes down in 3 m in 25 meters. If the water at the upstream face stands flushed with the crest and assuming no hydrostatic pressure uplift. Compute the location point along the base (measured from the toe) where the resultant force intersects it. The specific gravity of concrete is 2.40
1. A rectangular dam with base equivalent to 2.5-meters and height equivalent to 6-meters holds water with an upstream height of 4.5-meters. Compute for the factor of safety against sliding and overturning. Unit weight of concrete is 23.54 kN/cu.m. Consider 1 meter length strip. Disregard hydrostatic uplift pressure. The coefficient between the dam and the foundation is 0.4.
For the dam given in the figure, compute for the total horizontal load, total vertical load, the factors of safety against sliding and overturning, the resultant of the forces, its location, and the total moment at the toe. coefficient of friction is 1.5, unit weight ng concrete is 2400 kg/m^3.
Answer the following: a. hydrostatic force acting on a wall b. weight of dam if the unit weight of concrete is 23.54 kn/cum c. overturning moment d. location of the resultant measured from the toe of the dam
A gravity dam of trapezoidal cross-section with one face vertical and horizontal base is 22 m high and has a thickness of 4 m at the top. Water upstream stands 2 m below the crest of the dam. The specific gravity of masonry is 2.4. FS(sliding) = 1.5
A cross-section of a concrete gravity dam is shown in figure. Analyze the stability of block A for empty and full upstream reservoir cases, separately. Ignore earthquake, silt wave and ice forces. Specific weights of concrete and water are 23kN/m3and 10kN/m3, respectively. Compressive and shear strengths of concrete are 35MPa and 6MPa, respectively. The coefficient of friction between concrete blocks is 0.65. There is no tail water in downstream. Safety factors will be ≥2 for overturning, will be ≥1.5 for sliding and will be ≥3 for shear sliding.
A masonry dam has a trapezoidal cross section, 25 m high, crest width of 3 m and base length 18 m. The upstream face slopes down 12 m in 25 m and the downstream faces slopes down 3 m in 25 m. If the water at the upstram face stands flushed with the crest and assuming no hydrostatic pressuruplift. Compute the location point along the base (measured from the toe) where the resultant force intersects it. The specific gravity of concrete is 2.40.