Shown here is a simplified representation of an electrical power plant and a house, with the source of electricity shown as a battery, and the only electrical "load" in the house being a single light bulb: Power lines Power plant House Why would anyone use two wires to conduct electricity from a power plant to a house, as shown, when they could simply use one wire and a pair of ground connections, like this? Power ines Power plant House

Shown here is a simplified representation of an electrical power plant and a house, with the source of electricity shown as a battery, and the only electrical "load" in the house being a single light bulb: Power lines Power plant House Why would anyone use two wires to conduct electricity from a power plant to a house, as shown, when they could simply use one wire and a pair of ground connections, like this? Power ines Power plant House

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
A power line is needed to connect a power station on the shore of a river to an island 4miles downstream and 1miles offshore. Find the minimum cost for such a line given that it costs $50 000 per mile to lay the wire under water and $30 000 pe mile to lay wire underground.
Basic Electrical Engineering You have been sent to a new home. The homeowner reports that sometimes the electric furnace trips the 240-V, 60-A circuit breaker connected to it. Upon examination, you find that the furnace contains three 5000-W heating elements designed to turn on in stages. For example, when the thermostat calls for heat, the first 5000-W unit turns on. After some period of time, the second unit will turn on, and then, after another time delay, the third unit will turn on. What do you think the problem is, and so would your recommendation for correcting? Explain your answer.
Explain the detailed process of Power Grid Extension
Electrical Engineering _ Energy Conversion Systems pls findthe question by using computer line. pls find fast.
draw a diagram of electric power and energy system with all the basic components, and list the name of components. And make following parts: what is the power plant? what is substation? what is transmission system, and what is distribution system? what is electric power network or power grid? what is power system? what is power and energy system? this subject name Electrical Engineering ..so please solve it clearly step by step
When electricity is transported from a power station to a city, the line voltage (relative to ground) is usually on the order of several hundred thousand volts. A power line cable has a radius of a = 2.0 cm, is made of aluminum with a resistivity of ρ = 2.7×10−8 Ω ⋅ m, and spans a distance of l = 100 km from a power station to a city. The city consumes 100 MW of power (so I2RL =100MW). (a) Find the resistance of the power cable between the station and the city(i.e.,between points A and B). (b) Suppose that the line voltage ∆VBC = 120 V. i. How much current is required to flow through the power line to deliver 100MW of power to the city? ii. How much energy is lost as heat between points A and B? (c) Suppose that the line voltage ∆VBC = 300 kV. i. How much current is required to flow through the power line to deliver 100MW of power to the city? ii. How much energy is lost as heat between points A and B?
A power plant produces 1000MW to supply a city 40km away. Current flows from the power plant on a single wire with resistance through the city and returns via the ground, with negligible resistance. At the power plant the voltage between wire and ground is 115 kV. Determine: (a) the current in the wire, and (b) the fraction of the power lost in transmission.
Lightbulbs are rated by their power consumption in watts (W). Electricity is sold in units of energy, which is power multiplied by time. Electricity costs vary widely across the United States and are on the order of 0.08–0.30 $/kW-hr for residential customers. Create a spreadsheet that utilizes electricity costs and the number of hours per day that a lightbulb is on as input variables. Then calculate the annual cost to operate a 60-W, 75-W, and 100-W incandescent bulb and the equivalent LED bulbs consuming 8, 10, and 16 W, respectively. Assuming the average household operates six 60-W, four 75-W, and two 100-W incandescent bulbs for 6 hours a day, how much money can they save in a year by changing all the bulbs to equivalent LED bulbs?
An electric heater can be modelled as a resistor. In Turkey heaters are designed and sold for 220V mains. Let us connect an electric heater to a 220V plug. The total power of the heater is 2kW. What is the current through the heater? If the heater is used in a country, where the mains voltage is 110V, what power is dissipated on the heater?
Describe the basic components of an electrical power grid and their functions.
Why do we need maximum power transfer? Explain.