Answered: Sieve # Maas retained (gr) 4 0…

Sieve # Maas retained (gr) 4 0 10 11,5 16 11,7 20 12 30 12,9 40 17,8 50 19,1 70 35,1 100 38,1 200 118 Pan 335 Draw grain size distribution curve,find D60, D30, D10 Classify the soil

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter5: Soil Compaction

Section: Chapter Questions

Problem 5.2P

See similar textbooks

Related questions

Q: Based on the below data from a sieve analysis test, what is the cumulative percent passing 630µm…

A: Cumulative percent passing 630 microne sieve= = (Cumulative mass retained on smaller size sieve /…

Q: SIEVE ANALYSIS Seive No. Sieve + Soil (g) Empty Sieve (g) 3/4" NA 1/2" NA 3/8" NA # 4 505.4 497.8…

A: Given data:

Q: Plot a combined graph for percent finer vs. grain size distribution for both the sieve analysis and…

A: Particle Size Distribution Curve is drawn to find out the composition of the soil and proposition of…

Q: Calculate the AASHTO group index number of the following soil Liquid Limit = 36% Plastic Index = 14%…

A: Solution; According to question;

Q: Cummulative Percent SIEVE ANALYSIS GRAPH Weight Retained (g) Retained (%) Sieve Size Percent Percent…

A: Soils are broadly classified as Coarse grained soils and fine grained soils. If more the 50% of soil…

Q: Evaluate the result of sieve analysis for fine aggregates as shown below Mass of soil * based on…

A: Given Seive No, Seive size, mass of soil with and without pan. Required % retained, sum (%retained),…

Q: Grain Size Analysis Problem Set No. 3 1. Following are the results of a sieve analysis: a) Determine…

A: In any Soil mechanics analysis it is important to know the type of soil its related property.…

Q: The following table shows a data set from a sieve analysis. (a) Complete the rest of the table.…

A: As there are multiple questions posted, according to the guidelines only the first three are being…

Q: 39. The following table shows a data set from a sieve analysis. (a) Complete the rest of the table.…

Q: 45 % and P Gravel is 55 %. answer the below questions: Amount Amount Sieve No. Retainded (g)…

A: Cumulative percentage retained for sand alone is shown in the table below.

Q: 2. Calculate the zero-air-void unit weight for a soil with Gs=2.75 for each given. w(%) Yav (kN/m³)…

Q: 1. Use the general definitions to derive the relation between the Moist Unit Weight, Specific…

A: Given data in question Moist unit weight Specific gravity Void ratio Volume of voids Volume of…

Q: Example: Marshall test results of surface course for six specimens gave the following results: Unit…

A: As per Marshall specifications, the optimum bitumen content can be found out by taking the average…

Q: Q2. Using the sieve results of a batch of sand and gravel shown in the table below,calculate the…

Q: Soil placed on a can has been weighed before and after an oven-drying procedure. The procedure…

Q: What is dry unit weight of the soil sample below (va) in Ib/ft ? The combined weight of a mold and…

A: Given data : Combined weight of mold and compacted soil sample (W1)=8.7 lbMold weight (W2)=5 lbmolds…

Q: Classify the soil by the Unified classification system. The results of the particle-size analysis of…

A: Introduction- A sieve review or gradation test is a process commonly used in construction management…

Q: Soil placed on a can has been weighed before and after an oven-drying procedure. The procedure…

Q: The back fill material for a vibroflotation project has the following grain sizes. D10 0.11 mm…

A: Find sorting coeffficient

Q: Sieve # Maas retained (gr) 4 0 10 11,5 16 11,7 20 12 30 12,9 40…

A: sieve mass cumulative weight reatained % cumulative weight 4 0 0 0 10 11.5 11.5 4.11 16…

Q: 29. The following table shows a data set from a sieve analysis. (a) Complete the rest of the table.…

A: KINDLY NOTE: As per our guidelines, we are supposed to solve the first 3 subparts. Kindly repost the…

Q: Three samples of aggregates were taken weighed in moist and dry condition. Moist Dry Unit Absorption…

Q: For a given sieve analyis: No. 4 - % finer 99%, for No. 200 -%finer 76. LL=60, PL=32. Classify the…

Q: TABLE P5.19 Amount Cumulative Amount Cumulative Percent Percent Sieve Size Retained, g Retained, g…

A: Sieve analysis data are mentioned below:

Q: Mass of Soil Sieve Opening Sieve # on each Sieve Size (g) 4 4.76 8 45 2.38 10 65 2.0 20 92 0.84 40…

Q: * Standard Reference of Water Content Determination is ASTM D 2216 O D ASTM 5321 O ASTM D 7687 O…

A: Which is Standard Reference of Water Content Determination?

Q: Determine its classification using USCS SP GW SW GP None of the above

A: Given, Sieve analysis data

Q: The back fill material for a vibroflotation project has the following grain sizes. D10 0.11mm D20…

Q: nere: MC = moisture content in percent Mmoist = mass of original specimen Mdry = mass of oven dry…

Q: SIEVE ANALYSIS Percent Passing Sieve No. Diam. (mm) Soil A Soil B Soil C # 4 4.76 100 100 100 # 8…

A: Given data:- Sieve No. Dia (mm) Percentage passing Soil A Soil B Soil C 4 4.76 100 100 100…

Q: C. Using the sieve results of a batch of sand and gravel shown in the table below,calculate the…

A: Finness modulus is the sum of cumulative percentage retained on each seive divided by 100.…

Q: What is the Summation of cumulative .1 retained percentage for the Sand 258 358 398 474

A: cumulative retained percentage =amount retainedtotal amount×100

Q: Q2/ It is desired to increase the density of (1000 bbls) of (11 ppg) to (13 ppg) mud. One gallon of…

A: We have to find the value of intial mud discarded and mass of API barite fequired and water volume…

Q: DATA AND RESULTS: SOLVE FOR ITS FINENESS MODULUS AND % ORGANICMATTER WT. RETAINED CUMULATIVE % OF…

Q: 1. The following are the results of a sieve analysis: U.S. Sieve No. Mass of Soil Retained on each…

A: Sieve analysis is a procedure for determining the particle size of granular material by passing it…

Q: 3. A soil weighing 150 grams is collected a day after heavy downpour, The size of the hole from…

A: Calculate the oven dry weight, percentage capillary water, and bulk density

Q: C) Soil classification and naming Net weight left on each sieve (gr) Sieve number 275 2" 185 1" 230…

A: (c) Soil classification and naming as per AAHSTO sieve analysis classification #4 > Gravel &…

Q: Data Sieve Sieve No. Opening (mm) 4 4.750 10 2.000 20 0.850 30 0.600 40 0.425 0.250 0.106 0.075 60…

Q: SITUATION 2: From the following data of a given sieve analysis: Sieve No. # 4 #8 #10 # 25 #60 #100…

Q: Q1. Using the British methods, design a concrete mix to bear an average compressive strength of 35…

A: Compressive strength of concrete = 35 MPa Dimensions of room slab = 5 x 4 x 0.2m…

Q: uS. STANDARD SIEVE NUMOERS HYDROMETER 1 r e va 16 200 100 .001 100 GRAIN SIZEN MILLIVETERS Sample…

A: for graph 1 Type - Sand Symbol - SP SP-(poorly graded sand)

Q: PLASIC LIMIT TEST Inal bwet (KN/m 3) bdny (KN/m 3) 1 128.6 105.2 132.4 109.4 3 134. 2 I11.4 LIQUID…

Q: We made sieve analysis for a soil sample, we had these results, complete the table. wt. retained on…

A: The seive analysis for soil sample calculation is shown in below table

Q: a. determine the effective size diameter d. determine the coefficient of uniformity c. determing the…

A: Given Data: Sieve Number Opening Size (mm) Mass Retained (g)

Q: a. 0.25 b. 0.50 4. For the soil with LL= 45%, PL = 25% and water content = 15% the liquidity index…

Q: Determine: 1. The percent finer in Sieve # 20 2. The percent finer in Sieve # 80 3. D60from the…

A: Find out : 1) % finer than sieve no 20 2) % finer than sieve no 80 3) D60 4) D30 5) D10 6) Cu…

Q: What is dry unit weight of the soil sample below (ya) in Ib/ft ? The combined weight of a mold and…

Q: calculate the suitability number and comment it as backfill material for soil having following grain…

A: Suitability number for Rating backfill has been defined by Brown in 1976, which is given as: S =…

Q: Mass Soil (A) weight retained %weight Mass Soil (B) Sieve % weight retained %weight Cumulative…

Q: Q2. Using the sieve results of a batch of sand and gravel shown in the table below and if the P sand…

A: Percentage of sand = 38 % Finness modulus is the sum of cumulative percentage retained on each…

Concept explainers

Soil engineering for highway design

Soil engineering is a part of geotechnical engineering that deals with the characteristics of soil. It also helps to understand the behavior of the soil in different conditions. The basic concepts of soil are studied to check the strength, compressibility, and porosity of the soil. This makes soil engineering an important topic for civil engineering.

Question

Sieve # Maas retained (gr)

4 0

10 11,5

16 11,7

20 12

30 12,9

40 17,8

50 19,1

70 35,1

100 38,1

200 118

Pan 335

Draw grain size distribution curve,find D60, D30, D10 Classify the soil

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Introduction

VIEW

Calculation

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat Problem 2.4 with the following data. 2.4 The following are the results of a sieve analysis. a. Determine the percent finer than each sieve and plot a grain-size distribution curve. b. Determine D10, D30, and D60 for each soil. c. Calculate the uniformity coefficient Cu. d. Calculate the coefficient of gradation Cc.
Calculate the CEC of a 100g soil sample that was found to contain the following cations: Ca2+ = 0.12g Mg2+ = 0.024g K+ = 0.078g Al3+ = 0.027g NH4+ = 0.036g H+ = 0.002g
U.S Sieve No Opening (mm) Mass of soil retained (g) 4 4.75 28 10 2.00 42 20 0.85 48 40 0.425 128 60 0.250 221 100 0.150 86 200 0.075 40 Pan 24 Determine the percent finer than each sieve and plot a grain-size distribution curve. Determine D10, D30, and D60 from the grain-size distribution curve. Calculate the uniformity coefficient, Cu. Calculate the coefficient of gradation, Cc. Classify the soil by AASHTO and USCS system. (LL = 30, PL = 10)
PLS ANSWER ASAPA WET OF SOIL SAMPLE HAS A VOLUME OF 4.85 x 10^-4 m3 AND WEIGHS 8.5N. AFTER OVEN DRYING, THE WEIGHT REDUCES TO 7.5N. IF sg = 2.7DETERMINE THE UNIT WEIGHT. DETERMINE THE MOISTURE CONTENT. DETERMINE THE DEGREE OF SATURATIONAnswer in 4 decimal places with unit
For an inorganic soil, the following grain-size analysis is given:Sieve No. % Passing4 10010 9020 6440 3880 18200 13For this soil, LL = 23% and PL = 19%. Classify the soil according to:a. The AASHTO soil classificationb. The Unified soil classification system
1. Calculate the amount of CaCO3 required to raise the pH of a hectare of this soil to pH6? (X-axis) Weight of lime added to 250g soil: 0,1,2,3,4,5. (Y- axis) pH: 3.58,5.05,6.56,6.76,6.94,6.96, respectively. 2. How many kg P/ha is 20 ppm P? ha= 2x 10^6; P= phosphorus
A 500g (assume no wastes) of dry soil was used for a soil mechanical analysis. Themass of soil retained in each sieve, and hydrometer analysis data are given in Table 1and Table 2, respectively.Table 1. Sieve Analysis DataUS SieveDiameter Mass Ret., g2.00 mm 101.40 mm 20500 μm 135150 μm 60250 μm 145850 μm 6075 μm 45 Particle PercentDiameter Passing, %20 μm 2.510 μm 1.52 μm 11. What is the value of the percent passing for sieve with 2 mm. opening inpercentage?2.What is the value of the percent passing for sieve with 150 μm. opening inpercentage?3.What is the value of the coefficient of uniformity?4.What are the percentages of gravel, sand, and Fines using the limits indicated byUSCS?5.What are the percentages of gravel,…
Classify the group symbol of the soil by USCS using the data given below: Percent passing the #4 sieve 68 Percent passing the #200 sieve 22 Liquid Limit 34 Plastic Limit 17 Group of answer choices SM SW SP SC
A WET OF SOIL SAMPLE HAS A VOLUME OF 4.85 x 10^-4 m3 AND WEIGHS 8.5N. AFTER OVEN DRYING, THE WEIGHT REDUCES TO 7.5N. IF sg = 2.7DETERMINE THE UNIT WEIGHT. DETERMINE THE MOISTURE CONTENT. DETERMINE THE DEGREE OF SATURATIONAnswer in 4 decimal places with unit
Calculate the coefficient of permeability of a soil sample of 6 cm is height and 50cm2 in cross sectional area, if the quantity of water equal to 450ml passed down in 10minutes under an effective constant head of 40cm. On oven drying, the test specimen weigh 495g. Take Gs as 2.65, calculate the seepage velocity of water during test.
A fully saturated soil sample has a volume of 28 cc. The sample was dried in oven and the weight of the dry soil pat was found to be 48.76 g. Given G= 2.68. Determine volume of solids in cm3. a. 18.23 b. 9.77 c. 20 d. 53.6
The moist unit weights and degrees of saturation of a soil are given in the table. y (kN/m3) S(%) 16.62 50 17.71 75 Determine: a. e b. Gs Show handwritten solutions.