SIMPLE STRESSES 15 KN/m 1. The beam shown in the figure carries distributed loads. Design the square (a x a) cross-section of the timber columns of the beam. 1.50 m 3 m 1 m Column A has the same dimensions 10 KN/m 1 m as Column B. The strength of the column is 80 MPa. Express the dimensions of the column in whole 10 KN/m A В number.

SIMPLE STRESSES 15 KN/m 1. The beam shown in the figure carries distributed loads. Design the square (a x a) cross-section of the timber columns of the beam. 1.50 m 3 m 1 m Column A has the same dimensions 10 KN/m 1 m as Column B. The strength of the column is 80 MPa. Express the dimensions of the column in whole 10 KN/m A В number.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

q2: A load P is supported by a structure consisting of rigid bar BDF and three identical 15-mm-diameter steel E = 200 GPa rods, as shown inthe figure. Use a = 2.705 m, b = 1.821 m, and L= 4 M.For a load of P = 117 kN, determine thedisplacement of joint F. Unit should be in mm
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 15 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm? A=600 mm? A= 300 mm? 2P 3P 4P P -3 m + 5 m -4m
QUESTION1) Figure Q1(a) show a simply supported beam of length L = 4.8m is and built for placing Machine and Magnum frame. The combined weight of the machine is approximated by uniform load 90kN/m along x3 = 2.4 m. For of the design, its assumed that the column framed located at a distance x1 and x2 = 0.8m and resulting concentrated load P1 and P2 exerted oneach beam is taken as 150kN and 150kN, respectively. The cross section of beam show as in Figure Q1(b). (a) Determine the bending stress at point a and the maximum bending stress of the beam (b) By referring Figure Q1(a) and consider section n-n, determine the maximum shear stress and the shear stress at point a.
q: A load P is supported by a structure consisting of rigid bar BDF and three identical 15-mm-diameter steel E = 200 GPa rods, as shown inthe figure. Use a = 2.787 m, b = 1.901 m, and L= 5 M.For a load of P = 136 kN, determine thedisplacement of joint D. Unit should be in mm
A short spiral column carries an axial dead load of 118 kN and an axial live load of 235 kN. Use fc’ = 27.5 MPa, fy = 414 MPa. Use U = 1.2D + 1.6L, Ф = 0.65 1. Assuming ρ = 0.01, which of the following gives the diameter of the column section? * a. 200 mm b. 215 mm c. 220 mm d. 300 mm 2. Which of the following gives the number of 16 mm diameter main bars? a 3 pcs b. 4 pcs c. 5 pcs d. 6 pcs 3. Which of the following gives the spacing of spirals? a. 10 mm Ф b. 55 mm Ф c. 60 mm Ф d. 65 mm Ф
Compute for the load in kN on a 3 cm diameter, 100 cm long steel rod it its maximum elongation exceed 0.12 cm. a. 178 b. 196 c.148 d. 287
USE 3 decimals; DRAW FREE BODY DIAGRAMS A 9-m simple beam is carrving a uniform load or 25 kN/m over the entire beam with two-point loads of 15 kN at 1.5 m from both ends. If E = 200 Gpa and | = 0.000332 m^4, determine the following using the Double Integration Method:a.) Midspan deflectionb. Deflection at 1.5 m from the eft reaction
The frame is used to support the wood deck in a residential dwelling. Sketch the loading that acts along the members BG and ABCD. a) Set b = 4.5 m, a = 2.4 m. Use Live Load = 1.92 kPa. b) Set b=2.4m, a=2.4m. Use Live Load = 1.92 kPa
Determine the diameter of each steel wire connected to the rigid members AB and DC. The members were originally horizontal. After the application of the 300 kN load, a vertical displacement of 1cm occurred at the point of application, let us say point I. Use E – 200 GPa.
A) Define the bending stress as relates of beams. B)A fixed AB length 3m carries a point load of 45KN at a distance of 2m from A.if the flexural rigity (i.e. EL)is 1×10^4KNm^2, determine: I) fixed end moment A and B II) Deflection under the load III) the maximum deflection IV) The position of the maximum deflection.
A steel column carries moment Mx = 11kN.m and My = 16.5 kN.m and an axial load of 220 KN. The steel section has the following properties:A = 7420 mm² ry = 50.4 mmSx = 693x10³ mm³ Sy = 186x10³ mm³K = 1.0 L = 6 mFy = 400 MPa E = 200000 MPaTx = 108 mm Cm = 0.85Axial compressive stress that would be permitted if axial force alone existed Fa = 72.54 MPa. Compressive bending stress that would be permitted if bending moment along the x-axis alone existed Fbx = 240MPa (0.60 Fy). Compressive bending stress that would be permitted if bending moment along the y-axis alone existed Fby = 300MPa (0.75 Fy). 1. Which of the following gives the axis compressive stress if axial load only existed. a. 30.45 MPa b. 27.82 MPa c. 28.46 MPa d. 29.65 MPa 2. Which of the following gives the bending stress if bending moment alone existed. a. 105 .48MPa b. 106.73 MPa c. 104.58 MPa d. 102.37 MPa 3. Using the…
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 16000 ksi] rods, and a solid steel [E = 32500 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.76 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.47 in. Assume L1=43 in and L2=79 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 26 kips is applied.