Kindly give me both right solutions with clear calculations. SITUATION 1: In the figure, the 50-m duct is 60mm in diameter.12 mPgage=205 kPa50 m - 60 mm dia.kgm3p = 917u = 0.29 Pa – sec|a. Compute the flow rate if the fluid has a density of 917 kg/m^3and absolute viscosity of 0.29 Pa-sec, inm3b. Compute the Reynolds number of flow.

Given data, Length of duct = 50 m Diameter = 60 mm Density of flowing fluid = 917 kg /m³ u = 0.29…

SITUATION 1: In the figure, the 50-m duct is 60mm in diameter. 12 m Pgage=205 kPa 50 m - 60 mm dia. kg m3 p = 917 µ = 0.29 Pa – sec a. Compute the flow rate if the fluid has a density of 917 kg/m^3 m3 and absolute viscosity of 0.29 Pa-sec, in . b. Compute the Reynolds number of flow.

SITUATION 1: In the figure, the 50-m duct is 60mm in diameter. 12 m Pgage=205 kPa 50 m - 60 mm dia. kg m3 p = 917 µ = 0.29 Pa – sec a. Compute the flow rate if the fluid has a density of 917 kg/m^3 m3 and absolute viscosity of 0.29 Pa-sec, in . b. Compute the Reynolds number of flow.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Incompressible steady flow in the inlet between parallel plates in the following figure is uniform,u=U0=az(zo-z),where a is a constant.If zo=4cm and the fluid is SAe 30 oil at 20°c ,What is the value of umax in cm/s?
Determine the pressure (in kN/m2) in the pipe shown (Pressure A) if y=1.24 m, h=1.02 m, and the manometry fluid is mercury (Specific Gravity=13.6).
In a pipe 300 mm in diameter, water flows over a length of 300 m, connecting point A, at topographic elevation of 100.0 m, in which the internal pressure is 291 kPa, to point B, at topographic elevation 74 .0 m, where the internal pressure is 334 kPa. Determine the direction of flow. Data: Specific gravity of water = 10 kN/m3. A) from B to A B) There is no drain. 0 C). from A to B For the previous question, calculate the pressure drop between A and B, in meters. ( ) If the flow is equal to 0.18 m3/s, calculate the friction factor of the pipe. ( ) For this same flow rate, calculate the friction velocity. ( )
A 300 mm x 75 mm venturi meter is inserted in a 300 mm diameterpipeline where water flows at 55 L/s. Neglecting friction loss,compute the drop in pressure head in meters from the inlet to thethroat.
The diameter of a pipe changes gradually from 6 inches at A to 18 inches at B. A is 15 ft lower than B. If the pressure at A is 10 lbs per square inch and at B, 7 lbs per square inch when there are 5.0 cubic ft per second flowing, determine: a. the direction of flow. b. the frictional loss between the two points B. If in Problem 1 the direction of flow is reversed, determine the pressure at A if all other factors, including the frictional loss, remain the same. C. In Problem 1, determine the diameter of pipe at B in order that the pressure at that point will also be 10 lbs per square inch, all other factors remaining constant. D. Determine the discharge in Problem 1, assuming no frictional loss, all other conditions remaining as stated. E. What would be the difference in pressure in pounds per square inch between A and B, Problem 1, if there were 6.2 cubic ft per second flowing, neglecting friction.
A smooth pipe with a constant diameter 0.20 m carries water at a temperature of 30oC (Refer Table Q4(c)). The Pipe pressure at section 1 and section 2 is 50 kPa and 20 kPa, respectively. Section 1 is located 2 m lower than section 1. Determine the head loss in the pipe.
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. a) Determine the head loss in the “smooth” pipe in meters if the friction factor is 0.014. b) What gage pressure p1 in kPa, is needed to provide the given flow rate?
Assume frictionless flow in a long, horizontal, conical pipe, where the diameter is 1.6m at entrance and 1m at exit. The pressure head at the smaller end is 9.5 kPa of water. If water flows through this cone at the rate of 4.2 m^3/s A.Find the velocity in (m/s) at them ENTRANCE. B.Find the velocity in (m/s) at the EXIT C.Find the pressure (in kPa) at the larger end
Q1 Given is a three-pipe series system, as in Fig. The total pressure drop is py — ps = 150,000 Pa, and the elevation drop is z4 — 25 = 5 m. The pipe data are Pipe L.om d, em e mm eld 1 100 8 024 0.003 2 150 6 0.12 0.002 3 80 4 0.20 0.005 The fluid is water, p = 1000 kg/m’ and v = 1.02 X 10~° m%s. Calculate the flow rate Q in mh through the system. o © 0O Al — —_— — B T U
With the chamber-pipe system in the figure, the ideal fluid (water) taken from the infinitely sized chamber A is poured into the atmosphere with a 40 cm fixed diameter BCDEF pipe. Since zB=29, zC=10, zD=28.5, zE=5 and zF=28 meters according to the comparison plane;a) Calculate the flow of the system.b) Draw the relative load (energy) and piezometer lines of the system.c) Determine where the greatest pressure will be observed throughout the system and calculate its relative value.
The water conveyed by a circular cross section pipe flows through the full section. The diameter of the pipe is D=0.5 m and the dynamic viscosity of the fluid is u = 1.2 x 10-3 N.s/m, its specific mass is p=1000 kg/m. Since the cross-sectional average velocity of the flow in the pipe is V= 0.5 m/s, determine the type of flow.
A venturi meter with a throat diameter of 100 mm is fitted in a vertical pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards. Two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet pipe 320 mm below the throat. The difference between the 2 gage pressure readings is 28 kPa. (a) Determine the flow in m^3/s neglecting head losses (b) Working from Bernoulli's equation, determine the difference in levels (in mm) between the two limbs of a mercury manometer if it is connected to the tapping points and the connecting pipes are filled with the same oil Draw illustrations Use 3 decimals