Situation 2: A rectangular beam has the following properties. Assume 12 mm stirrups. Assume a single layer of reinforcements. Calculate Mu. Given: Width of the beam, = 450 mm Over-all depth, h = 600 mm Tension reinforcements = 10 pcs 36 mm dia Comp reinforcements = 4 pcs 28 mm dia Specified strength of concrete, f'c 28 Мра Steel yield strength, fy = 415 MPа Note: Round off your final answer in 3 decimal places. No need to type the units.

Situation 2: A rectangular beam has the following properties. Assume 12 mm stirrups. Assume a single layer of reinforcements. Calculate Mu. Given: Width of the beam, = 450 mm Over-all depth, h = 600 mm Tension reinforcements = 10 pcs 36 mm dia Comp reinforcements = 4 pcs 28 mm dia Specified strength of concrete, f'c 28 Мра Steel yield strength, fy = 415 MPа Note: Round off your final answer in 3 decimal places. No need to type the units.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2.1 Determine the shear strength of concrete Vc per equation (c) of table 22.5.5.1 in ACI318-19
Q2: (10 %) of concrete samples have compressive strength less than (30 mn/m2) and (20%) have strength greater than (36mn/m2), if the minimum acceptable strength is (28 mn/m2). What is the prob. that sample will have strength fess them the minimum (one unitin LS.D.=1}7
Determine the development length required in bar diameter for the epoxy-coated bottom bars of the beam with 4 - 25mmΦ longitudinal bars annd 10mm stirrups @ 200mm o.c., bw = 400mm, side and bottom cover = 80mm, spacing between bars is 80mm o.c., normal concrete with f'c = 21 MPa, fy = 420 MPa. Consider Ktr in calculation. Express your answer in whole number.
b) Using first principles analyze a rectangular beam for having 230 mm width and 550 mm effective depth is reinforced with steel An on tension side only. Taking parameters with the usual notation as k = 0.36, k2 = 0.42 and Eru = 0.0035 determine for concrete of grade M2s and steel of grade Feso obtain. Xu mar, Mur max, As max for balance section; Mur for Au = 800 mm?:
Give full explanation Awall form 14 ft high is filled with 160 lb per cu ft concrete at a tem perature of 70°F. The concrete is Type I without a retarder. Concrete will be placed with normal internal vibration to a depth of less than 4 ft. The rate of placement is 5 ft per hr. From Table 1, the value of Cw is 1.1 and from Table 2 the value of Cc is 1.0. The rate of placement is less than 7 ft per hr and the place ment height does not exceed 14 ft so calculate the lateral pressure by using appropriate formula.
29 A square footing 2.3 m x 0.35 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 345 kN LL = 204 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal one way shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.
A light-weight concrete was cast-in-place to form a rectangular beam. If its unit weight is 17.24 kN/m3, and its compressive strength is 27 MPa, determine its Modulus of Elasticity in MPa. Round-off only on your final answer, in three-decimal places. need it asap pls
Determine the weight of rebar reinforcement for the tunnel concreting works per specifieddiameter, using the following considerations:a. Rebars are assumed at 150 kg per cubic meter of concrete.b. Proportions:i. 32-mm dia. Rebar = 30%ii. 25-mm dia. Rebar = 25%iii. 20-mm dia. Rebar = 20%iv. 16-mm dia. Rebar = 15%V. 10-mm dia. Rebar = 10%
Practice Problem 1Based on the structural analysis performed in a simply-supported reinforced concrete beam, it yields the following values of un-factored (service) loads. Floor Dead Load = 80 kN, Floor Live Load = 10 kN/m, Wind Load = 60 kN, and Earthquake Load = 50 kN. The 10m beam has a dimension of 500 mm x 500 mm and the unit weight of concrete used is 24 kN/m^3. Use the provisions stated in NSCP 2015.a) Determine the critical factored load in kN.b) Determine the critical factored moment in kN-m. Practice Problem 2A 5m reinforced concrete beam, with dimensions 300 mm x 500 mm, has a superimposed dead load of 20kN/m and a live load of 10kN/m. If the unit weight of concrete used in the beam is 24 kN/m^3, what would be the total service load carried by the beam?
A hollow concrete masonry unit has an actual dimension of 150mm x 200mm x 400mm(W x H x L). The unit was tested in a compression machine with the following result.Failure load = 1,200 kNNet volume = 4,400,000 mm3Determine: a) the gross area compressive strength.b) the net area compressive strength.
1- For the floor system shown in Figure below, support service live load 4KN / (m ^ 2) and service dead load 5KN / (m ^ 2) Answer the flowing. Classify the floor system into one way or two-way solid slab. 2- What is the minimun slab thickness that should be used to control deflection and shear requirement ? 3- By using Ø 12 mm rebar, what is the required positive and nagative reinforcement? 4- Sketch the detail of reinforcement. Use : fy = 400Mpa , f c ^ prime =30 Mpa 6.00 m 6.00 m6.00 m 3.00 m 0.30 m АB 3.00 m 3.00 m
Compare materials quantity for M30 grade of concrete?