Situation 4 The frame shown in Figure AN-33 is to be analyzed using the portal method. 10. Which of the following most nearly gives the axial 8m 6 m 30 KN E force on member DE in KiloNewton. a. 1.875 c. 9.375 b. 37.5 d. 28.125 60 KN 11. Which of the following most nearly gives the moment at D in KiloNewton-Meter. b. 135 d. 90 following most a. 67.5 Figure AN-33 C. 32.5 12. Which of the nearly gives the shear member ЕН in on KiloNewton. а. 30 b. 15 c. 22.5 d. 7.5 w9

Situation 4 The frame shown in Figure AN-33 is to be analyzed using the portal method. 10. Which of the following most nearly gives the axial 8m 6 m 30 KN E force on member DE in KiloNewton. a. 1.875 c. 9.375 b. 37.5 d. 28.125 60 KN 11. Which of the following most nearly gives the moment at D in KiloNewton-Meter. b. 135 d. 90 following most a. 67.5 Figure AN-33 C. 32.5 12. Which of the nearly gives the shear member ЕН in on KiloNewton. а. 30 b. 15 c. 22.5 d. 7.5 w9

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Before the load P was applied, a gap, ?0(2.75mm) existed between the cantilever beam AC andthe support at B. Knowing that E=200 GPa, determine the magnitude of P for which thedeflection at C is δ(5.5mm) and the reaction at B. (Hint: Use the method of superposition and beam deflections in Appendix A)
Calculate V(x) and M(x) between x = 2ft and x = 7ft (measured from the left end) of thebeam below: Ay = +1865 # (upwards) and MA = +3765 ft#(counter-clockwise); the support reaction at the roller C is Cy = +675 # (upwards). There isa HINGE at B, with internal forces bx = 0 and by = ±175 #.
Please only solve 12.15 PLEASE EXPLAIN TO ME HOW TO FIND THE LOCATION OF THE RESULTANT, I don't know how to take the moment about the buttom for each area, please explain, thank you
Solve fast please I need correct answes
22 Determine the plastic moment strength (kN-m) of a C15x40, A992 steel, about the minor axis. d = 381 mm bf = 89.41 mm tw = 13.21 mm tf = 16.51 mm A. 36.24 B. 30.98 C. 43.11 D. 50.41
Find the slope and deflection at B and E of the beam and loadings shown using unit load method. The section of the beam is tubular with outer diameter of 500mm and inner diameter of 200mm. E=20GPa. (point B is not an internal hinge. clue:YE=0.08 mm, θE=8.07 X 10^−6 rad, θb=2.04 X 10^−6 rad, Yb =0.00278 mm).
The roof is supported by cables as shown in the photo. If the cablesexert forces FAB = 100 N and FAC = 120 N on the wall hook at A asshown , determine the resultant force acting at A. Expressthe result as a Cartesian vector.
Design a most economical spiral-column cross-section to support factored forces and end moments of Pu = 1,600 kips and Mu = 150 kip-ft. Assume that the centroid of each longitudinal bar from the edge of the column is 2.5 inch. What is the trial diameter dimension of the section in inch if ρg = 0.025?
The length of the 3/32 in.diameter steel wire CD has been adjusted so that with no load applied, a gap of 1/16 in. exists between the end B of the rigid beam ACB and a contact point E. Knowing that E=29 X 10⁶ psi, determine where a 50-lb block should be placed on the beam in order to cause contact between B and E.
Determine the reactions at a and b for the beam subjected to the concentrated loads Ay= ? (Not 8.77 or 4.85 previous failed attempts on my behalf) bx = 7.2 Ax = ? (Not 1.9 or -.3365)
From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m and EI = 200MNm^2Determine the following;C. Slope at L/3. D. Deflection at L/3.
A tapered cantilever beam AB supports a concentratedload P at the free end (see figure). The crosssections of the beam are rectangular with constantwidth b, depth dA at support A, and depth dB = 3dA/2 at the support. Thus, the depth d and moment of inertiaI at distance x from the free end are, respectively, d = (dA/2L)(2L+x) I=(bd3/12) =(bd3A/96L3)(2L+x)3 = (IA/8L3)(2L+x)3in which IA is the moment of inertia at end A of thebeam.Determine the equation of the deflection curveand the deflection δA at the free end of the beam dueto the load P.