Situation 6: A built-up beam is composed of the following: bf = 360mm tf = 28.0mm d = 600mm tw = 20 . All plates are A36 steel with Fy = 250MPa and the flanges are continuously connected to the web by means of fillet welds. The beam is simply supported at its end and laterally supported only at supports. Cb = 1.0 1. Which of the following nearly gives the moment capacity of the beam if it has a span of 4.0 meters? 1055 KN-m 1090 KN-m 1070 KN-m 1080 KN-m

Situation 6: A built-up beam is composed of the following: bf = 360mm tf = 28.0mm d = 600mm tw = 20 . All plates are A36 steel with Fy = 250MPa and the flanges are continuously connected to the web by means of fillet welds. The beam is simply supported at its end and laterally supported only at supports. Cb = 1.0 1. Which of the following nearly gives the moment capacity of the beam if it has a span of 4.0 meters? 1055 KN-m 1090 KN-m 1070 KN-m 1080 KN-m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

Refer to the given figure below and compute for moment at force C -- (CW+) Mc
Two d mm*10 mm cover plates are welded to two UPN 200 channels 100 mm high to form the cross section of the compound beam shown in the figure. The moment of inertia of each channel about a horizontal axis through the centroid is 19.10*106 mm4. a) Determine the support reactions. b) Draw the shear force and bending moment diagrams. c) If the allowable bending stress of the beam is 300 MPa, find the required width d of the plates to safely support the load.
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. Calculate the depth of the neutral axis of the section in PART B in mm.0 Calculate the stress in the steel of the section in PART B in MPa.0 Calculate the ultimate moment capacity of the section in PART B in kN.m.0
The beam is subjected to loads as shown. 1. Compute the total moment about point B. 2. Identify the location of the resultant from point A.
The Warren truss loaded shown in the figure P-418 below is supported by a roller at C and a hinge at G. By method of sections, compute the force in the members EF, DF, and GE.
Determine the absolute maximum bending moment along the beam. a. 550lb-ft b. 350lb-ft c.732lb-ft d. 995lb-ft
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. Calculate the depth of the neutral axis of the section in PART A in mm.0 Calculate the ultimate moment capacity of the section in PART A in kN.m.0 Calculate the effective depth of the section in PART B in mm.0
7. Considering sag rods and tie rods at third points, what is the interaction value for combined moment? (2 decimal places) A 20m Fink Truss are spaced at 'S' meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is 'RLL' N/m2 of roof surface and roof covering is assumed to be 'RDL' N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings. Fy = 248 MPa. C10X20 properties: w=29.76kg/m, A=3787.09mm2, Ix=32.84x106mm4, Iy=1.17x106mm4, Zx=317.91x103mm3, Sx=258.92x103mm3, Zy=44.25x103mm3, Sy=21.47x103mm3 S (m) RLL (N/m^2) RDL (N/m^2) 6.00 900 900
3. Considering sag rods and tie rods at midspan, what is the interaction value for combined moment? (2 decimal places) A 20m Fink Truss are spaced at 'S' meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is 'RLL' N/m2 of roof surface and roof covering is assumed to be 'RDL' N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings. Fy = 248 MPa. C10X20 properties: w=29.76kg/m, A=3787.09mm2, Ix=32.84x106mm4, Iy=1.17x106mm4, Zx=317.91x103mm3, Sx=258.92x103mm3, Zy=44.25x103mm3, Sy=21.47x103mm3 S (m) RLL (N/m^2) RDL (N/m^2) 6.00 900 900
f) the maximum bending moment in the beam. Enter your answer in kNm to 3 decimal places.
A reinforced T-beam has an effective depth of 650 mm and is reinforced with 7-25 mm diameterbars. The web width is 330 mm and has a flange thickness of 120 mm. The beam has a span of 7m and has a spacing center to center equal to 2.5 m, fc’ = 21 MPa and fy = 350 MPa.Compute the nominal moment capacity of the beam for positive bending in kN m. Express youranswer in one decimal place.
From the given truss shown, compute the force in member DE. a.62.5 N (C) b.187.5 N (C) c.62.5 N (T) d.37.5 N (C)