Situation 6: A steel plate is 280 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy = 248 MPa and Fu = 400 MPa Given: S1 = 65mm, S2 = 65mm, S3 = 75mm, g1 = 80mm, g2 = 70mm, g3 = 70 mm $1 52 gl T g2 g3 DO E s3 1. Which of the following nearly gives the critical net area? O 3570 mm^2 3366 mm^2 O 3231 mm^2 O 3471 mm^2 BO

Situation 6: A steel plate is 280 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the plate as shown. Hole diameter = diameter of bolt + 2 mm. Use Fy = 248 MPa and Fu = 400 MPa Given: S1 = 65mm, S2 = 65mm, S3 = 75mm, g1 = 80mm, g2 = 70mm, g3 = 70 mm $1 52 gl T g2 g3 DO E s3 1. Which of the following nearly gives the critical net area? O 3570 mm^2 3366 mm^2 O 3231 mm^2 O 3471 mm^2 BO

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the service tensile load capacity for an angle bar L 125 x 75 x 12 A53 steel connected with 13 A490 bolts as shown in the Figure 2. Diameter of holes is 3mm larger than the bolt diameter. Bolt diameter = 13 mm Standard hole = 24 mm Use hole diameter = 13 + 3 = 16 mm a = 43.5 mm b = 51 mm c = 36 mm d = 252 mm
The figure shows a plate having a width of 400 mm and thickness of 12 mm is to be connected to another plate by 34 mm diameter bolts as shown in the figure. Assume diameter of holes to be 2 mm larger than the diameter of the bolts. Use A 36 steel plate with yield strength Fy = 248 MPa and minimum tensile strength Fu = 400 MPa. For a chain holes extending across a part in any diagonal or zigzag line, the net width of the part shall be obtained by deducting from the gross width the sum of the diameters or slot dimensions of all holes in the chain and adding, for each gage space in the chain, the quantity S24g where S is the longitudinal center to center (pitch) of any consecutive holes, in millimetres and g is the transverse center to center spacing (gage) between fastener gage lines in millimetres. If a = 60 mm, c = 150 mm and d = 100 mm. Determine the nearest value of “b” so that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. Determine the nearest value…
For part A: I got 6.64 in and 0.0108 or 1.08% For part B: Please compute the R value: R=ρfy(1-a/2d) Then compute the Mt value: Mt=Rbd^2 Please show how to get units in kip ft For part C: Please solve
The cast iron block with cross-sectional dimensions of 62.5 mm by 62.55 mm consists of two pieces. The pieces are prevented from sliding along the 55 deg inclined joint by the steel key, which is 62.5 mm long. The working stresses are 275 MPa for cast iron bearing and 345 MPa for the key in shear. If the block is loaded with P=287 kN, calculate the required dimension "h" of the key. Write your final answer in 2 decimal places with the unit of mm.
column section =ISEB500 bracket plate thickness=11mm p=450KN E=270mm p=5mm bolt size =M20
Calculate the maximum shear force in the bolts and the required diameter in the figure. What is the maximum shear force on the bolt in kN?(2 decimal places) What is the required diameter on the bolt considering A325 bolts in mm? (rounded value) X= 125mm, Y= 150mm, P= 30
W 10x45 is connected to two plates with two lines of ¾” bolts as shown below. Determine the tensile strength of the system if Fy = 50 ksi and Fu = 65 ksi.
If the allowable bearing stress in the bolt is 18.855 ksi. what is the minimumrequired diameter of the bolt at B? b= .75” h= 7.874” Distances are in feet.
All three pins are to have the same diameter. Determine the minimum pin diameter that may be used. d= ? (unit mm)
The tension member shown in the figure contains holes for 3/4-in Ø bolts. At what spacing, s, will the net area for the section through one hole be the same as a rupture line passing through two holes? (Ans. 3.24 in)
A=7B=7D=2C=5E=8F=4Change letters into numbers... Determine the total area (mm2) of the given section. ( Locate the centroid (mm) of the section from the top
The small postal scale consists of a counterweight W1, connected to the members having negligible weight. Determine the weight W2 that is on the pan in terms of the angles θ and Φ and the dimensions shown. All members are pin connected.