Situation 7: A 600 mm x 600 mm tied column reinforced with 16- 32 mm diam. Using f'c-28 Mpa and fy -415 Mpa. Size of aggregates used is 25 mm. 18. Compute the safe ultimate load that the column could carry. 19. Compute the spacing of the 10 mm wires. 20. Compute the maximum clear distance of main bars.

Situation 7: A 600 mm x 600 mm tied column reinforced with 16- 32 mm diam. Using f'c-28 Mpa and fy -415 Mpa. Size of aggregates used is 25 mm. 18. Compute the safe ultimate load that the column could carry. 19. Compute the spacing of the 10 mm wires. 20. Compute the maximum clear distance of main bars.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the Pn of the following column assuming it had no moment on it and only an axial compression force: (f’c = 6000 psi, Grade 60 bars, h = 20”, b = 12” (i.e. rectangular section), tied column). Do not worry about calculating φ (phi factor). You can assume it is a short column. Also assume a reinforcement ration of 2% (ρg = 0.02).
A circular, tied column 440 mm in diameter is reinforced with 12 16-mm-dia. vertical bars. Calculate the design axial strength of the column in kN. Use material strengths f'c = 28 MPa and fy = 420 MPa.0
A spiral column carries a service dead load of 1000 kN and a service live load of 900 kN. fc' = 27.5MPa and fy = 413.5 MPa. Using a steel ratio of 0.03 a. What is the diameter (mm) of the spiral column?b. How many pieces D28 longitudinal reinforcement is required?c. Determine the possible spacing (mm) of the 10 mm spirals assuming a 40 mm concrete cover.
Q1. Determine the vertical displacement of end C of the precast concrete column. Econcrete = 4.2 (10³) ksi.
SITUATION A: The floor system shown has the following applied loads. Super Imposed Dead Load = 2.00 kPa Live Load = 1.90 kPa Slab Thickness = 100.00 mm Weight of Concrete = 24 kN/m3 Self-Weight of the beam = 1.92 kN/m Material Specifications: f’c = 21.00 MPa fy = 345.00 MPa Steel Cover = 50.00 mm What is the maximum positive moment of beam BE, acting on the midspan? in kN-m What is the maximum steel ratio of the section located at the supports? What is the actual steel ratio of the beam section at the supports? What is the ultimate moment capacity of the beam at the supports? in kN-m What is the effective flange width at the midspan? in mm What is the height of the compression block of the section at midspan? in mm What is the ultimate moment capacity of the beam at the midspan? in kN-m What would be the height of the CHB that can be placed on beam BE? Assuming the weight of the blocks is 2.30 kN/m per meter height? in meters
Principles of Reinforced and Prestressed Concrete If assumptions are made, verify if assumptions are correct. A reinforced rectangular beam with a with of 275 mm and effective depth of 440 mm has 4 16mm bars placed in 1 layer at the tension side. The beam has a stirrup with diameter of 10mm. Use fc'=28MPa and fy=420MPa, L=3.85m, w0=19.25kN/m and wl=24.75kN/m. 1. Calculate the nominal moment capacity if the beam. 2. Calculate the strain of the tension bars. 3. Calculate the strength reduction factor of the beam.
Principles of Reinforced and Prestressed Concrete If assumptions are made, verify if assumptions are correct. A reinforced rectangular beam with a with of 275 mm and effective depth of 440 mm has 4 16mm bars placed in 1 layer at the tension side. The beam has a stirrup with diameter of 10mm. Use fc'=28MPa and fy=420MPa, L=3.85m, w0=19.25kN/m and wl=24.75kN/m. 1. Calculate the nominal moment capacity if the beam.
A rectangular beam has a width of 330 mm and an effective depth to the centroid of the tension reinforcement of 432.5 mm. The tension reinforcement furnished is 7- 28 mm dia. bars and that for compression reinforcement is 4- 22 mm dia. bars placed 62.5 mm from the compression face of the beam. fy = 410.3 MPa and f'c = 35.9 MPa. Answer the following: (1) Determine the depth of the compression block. (2) Determine the design strength using 0.90 as the reduction factor. (3) Determine the concentrated live loads at the midspan in addition to the dead load of 19.7kN/m including the weight of the beam if it has a span of 9 m.
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
A T beam for a floor system has a slab thickness of 100mm and total depth of 550mm. bw=300mm. The beam has a span of 6m with a spacing of 2.4m center to center. The beam carries a live load moment of 184 kN.m and dead load moment of 84 kN.m f'c = 20.7 Mpa, fy= 413.7. Steek cover = 65mm A.Determine the effective flange width (m) B.Determine the depth of concrete compression block (mm) C.Determine requires steel area,(mm^2)
Find the maximum axial compressive service loads that the column of crosssection shown can carry. The column is short. Assume that the service dead load and live load are equal. Check the ties.Use f′c=4000 psi and fy=60,000 psi.
A square tied column 400 mm by 400 mm is reinforced with 8-20mm diameter bars with fy = 410 MPa. Calculate the safe service axial dead load if the safe service axial live load is 924 kN. Use f’c = 20.7 MPa.