SITUATION: A steel tape with coefficient of linear expansion of 0.0000116 per °C is known to be 50 m long at 20°C. The tape was used to measure a line which was found to be 532.28 m long and when the temperature was 35°C. Zoom image Find the temperature correction for the measured line. 0.0691 0.0861 O 0.0816 0.0619

SITUATION: A steel tape with coefficient of linear expansion of 0.0000116 per °C is known to be 50 m long at 20°C. The tape was used to measure a line which was found to be 532.28 m long and when the temperature was 35°C. Zoom image Find the temperature correction for the measured line. 0.0691 0.0861 O 0.0816 0.0619

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter7: Length And Length-related Variables In Engineering

Section: Chapter Questions

Problem 42P

See similar textbooks

Similar questions

What must be the pull in a 70 meters tape in order to eliminate the sag and temperature correction, given the following? a = 7x10% m? E = 2x101 N/m? Weight of tape, 11 N Po = 10kg To = 22°C T = 20°C K= 0.0000116/°C The tape length is supported at both ends.
What must be the pull in a (7)(10) meters tape in order to eliminate the sag and temperature correction, given the following? a = 7x10% m? E = 2x101 N/m? Weight of tape, 11 N Po = 10kg To = 22°C T = 20°C K= 0.0000116/°C The tape length is supported at both ends. Fundamentals of surveying
What must be the pull in a 70 meters tape in order to eliminate the sag and temperature correction, given the following? a = 7x10^-6m? E = 2x10^11N/m? Weight of tape, 11 N Po = 10kg To = 22°C T = 20°C K= 0.0000116/°C The tape length is supported at both ends.
A 50 m steel tape is used to measure a rectangle at 20°C with a pull of 55 N. The sides are recorded as 155.90 m and 121.00 m. The average temperature during measurement is 30°C with a pull of 55 N. C = 0.0000116/°C.16. Find the error in area.
A 100 m tape weighing 3 kg was standardized and found to be 0.02 m short at temperature of 10degC and a 30 N pull when supported throughout. The 1324.55 – meter distance measured is an inclined distance whose difference in elevation between the points is 2 m. What is the correct distance? a. 1 324.28 m b. 1 234.18m c. 1 345.83 m d. 1 432.11 m
What must be the pull in a 30m tape in order to eliminate the sag and temperature correction, given the following? a = 6x10^-6 m^2 E = 2x10^11 N/m^2 Weight of tape = 11 N Po = 7 kg To = 22 degrees Celcius T = 20 degrees Celcius K = 0.0000116/degrees celcius The tape length is supported at both ends.
A line was determined to be 2,651.56 meters when measured with a 30 m. steel tape supported throughout its length under a pull of 4 kg. at a mean temperature of 39 °C. Tape used is of standard length of 15 °C under a pull of 5 kg. Cross-sectional area of the tape is 3.95 mm^2. Determine the TOTAL ERROR of the LINE due to TEMPERATURE in meters. Round off to three decimal places. Input the magnitude only.
A steel tape with C=0.0000116 per degree centigrade is known to be 50 m long at 20 °C. The tape was used to measure a line 500 m long when the temperature was 35°C. What is the corrected length of the line?
A 30 m steel tape is used to measure a rectangle at 22°C with a pull of 42 N. The sides are recorded as 155.90 m and 121.00 m. The average temperature during measurement is 32°C with a pull of 42 N. C = 0.0000116/°C. Compute the total correction for the length Compute for the total correction for the width What is the true area of the rectangle?
A 30-meter steel tape is 3 mm too long at 25°C with a pull of 60 N. A rectangle is measured with this tape. The sides are recorded as 145.49 m and 131.05 m. The average temperature during the measurement is 31°C with a pull of 60 N. What is the error in area in square meter?
Using the following notes, what is the elevation of BM14?Station BS FS Elev.BM12 4.64 209.651 5.80 5.06 2 2.25 5.02BM13 6.02 5.853 8.96 4.944 8.06 3.225 9.45 3.71 6 12.32 2.02BM14 1.98
Please calculate for D and please explain how to input the angle 2°54'13'' in the calculator. D = 1/tan(2°54'13''/2)