Situation A. | Six steel cables support a circular moulding of diameter 2 meters. The cables are spaced equally along the perimeter of the moulding. The moulding weighs 2.50 kN/m. Note: Do not round off during calculations, use the store functions of your calculator. 1) If the allowable stress is 124 MPa, determine the minimum diameter of each cable. (mm) 2) If the diameter of the cable is 10mm, determine the vertical displacement of the moulding. (mm)

Situation A. | Six steel cables support a circular moulding of diameter 2 meters. The cables are spaced equally along the perimeter of the moulding. The moulding weighs 2.50 kN/m. Note: Do not round off during calculations, use the store functions of your calculator. 1) If the allowable stress is 124 MPa, determine the minimum diameter of each cable. (mm) 2) If the diameter of the cable is 10mm, determine the vertical displacement of the moulding. (mm)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following system is made up of two bars of A-36 steel with a cross-sectional area of 12cm x 15cm. The pins have a diameter of 4cm and are made of 304 stainless steel and the cable has a diameter of 2cm and is made of A-992 steel and the load is 50 kg. 1. Determine the stress transformation.2. Calculate the failure theory according to Von Mises.
Calculate the stress in cable E for the beam setup shown. Cable E has a diameter of 20 mm.
PLEASE ANSWER THIS FOR 3O MINUTES. A. DETERMINE SUPPORT REACTION B. DETERMINE STRESS IN THE CABLE C. DRAW FREE BODY DIAGRAM
Determine the stress of 5-mm radius cable CD that supports the bar AB at 150-kilograms and a 2,000 kg/m² force at point A. Hint: W=m*g
A rectangular gate, 1m wide supports water as shown in the figure below. The gate is hinged at the bottom and is kept in a vertical position by a concrete clock ( ϒ=23.6KN/m3 ) connected by a cable. a) Determine the hydrostatic force acting on the gate. b) Determine the tension in the cable assuming a minimum volume of concrete block is keeping the gate in a vertical position. c) Determine the minimum volume of concrete block required.
Calculate the working stress on the 1/2-inch diameter cable as shown on the figure below. The bar has a uniformly weight of 66 lbs. FN = 78kips
Given the Cable as shown below that weighs 4.0 N/m with 30 Nhorizontal load applied at the roller support at Point B.Determine the following:a.) The Span of the Cable L.b.) The Maximum Tension in the Cable.c.) The Minimum Tension in the Cable.
Determine the tension P in the cable which will give the 100 lb-block a steady acceleration of 5 ft/sec^2 up the incline.
Take the allowable stress in the cable as 2000 MPa, and determine for what value of θ the cost of material used in the cable structure below will be minimum, and also determine the total volume of the material.
the cable reel is in contact with the ground at A and wall B with a weight of 100 kg. If the static friction coefficient between the roller and the contact surfaces is Ms = 0.3, find the smallest force P that will cause the roller to rotate.
If the motor exerts a constant force of 300 N on the cable, determine the speed ofthe 20-kg crate when it travels s = 10 m up the plane, starting from rest. The coefficient of kineticfriction between the crate and the plane is μk = 0.3. PWE
AB, a rectangular (0.6 mx0.9 m) sluice gate, blocks a liquid with a gravity of 0.79. The weight of the floodgate is 300 N, and find the force that must be applied to the Cable BCD to open the surface Please tell me the process of solving