SITUATION II: A propped 10 m cantilever beam is required to carry a load of 100 kN at midspan. If the yield stress of mild steel is 300 MPa, 6) Compute the plastic section modulus of the given beam. 7) Compute the elastic section modulus of the beam given that the shape factor is equal to 1.69. 8) Compute for the plastic moment of the given beam if an additional uniform load of 5kN/m is distributed along its total length.

SITUATION II: A propped 10 m cantilever beam is required to carry a load of 100 kN at midspan. If the yield stress of mild steel is 300 MPa, 6) Compute the plastic section modulus of the given beam. 7) Compute the elastic section modulus of the beam given that the shape factor is equal to 1.69. 8) Compute for the plastic moment of the given beam if an additional uniform load of 5kN/m is distributed along its total length.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow box beam has an outside dimension of 400 mm x00mm and inside dimension of 300 mm x 500 mm (uniformthickness of 50 mm) has a fixed ended span of 6 m.1. Compute the plastic section modulus.2. Compute the plastic moment capacity of the beam.3. Which of the following gives the safe uniform loaddistributed horizontally that the beam could carry beforecollapse if Fy = 250 (Plastic Analysis using Virtual Work Method) show complete and detailed solution pls.
The wide flange beam shown supports the concentrated load ? and a total uniformly distributed load of 2?. Determine the maximum safe value of ?i f flexural stress ?? ≤ 10 ??? in tension, ?? ≤ 20 ??? in compression and shear stress ? ≤ 1.4 ???.
A simply supported beam has a maximum moment equal to 25 KN.m. The beam has a width of 200 mm and a depth of 250 mm and is made up of 80% grade Narra. Use dressed dimension by reducing its dimensions by 10 mm. What is the actual bending stress of the beam in MPa?
A pre stressed concrete simple beam having a cross section of300mmx600mm is subjected to a pre stressing force in steel whicheventually reduce to 1200KN due to losses acting on a parabolic tendons.The beam carries a total uniform distributed load of 20 KN/m includingbeam’s weight. Using three methods calculate the total stresses at midspan section of the beam. Given:B = 300mmD = 600mmP = 1200KNW = 20 KN/mE @ mid span = 50 mmE @ end section = 0 mmL = 10 mm Det. the total stresses of the extreme bottom fiber at midspan using load balancing method. (Mpa)
A propped 10 m cantilever beam is required to carry a load of 100 kN atmidspan. If the yield stress of mild steel is 300 MPa Compute the plastic section modulus of the given beam.7) Compute the elastic section modulus of the beam given that the shape factor isequal to 1.69.8) Compute for the plastic moment of the given beam if an additional uniform loadof 5kN/m is distributed along its total length.9) Calculate for the nominal/effective moment of the beam (with the 100 KN andthe 5KN/m loads), using a reduction factor of 0.90.10) Calculate for the nominal/effective moment of the beam (with the 100 KN andthe 5KN/m loads), using a safety factor of 1.67.
It is assumed that the total weight W (kN) in a rigid slab, single-span, single-storey undamped construction model is summed at the floor level. The total stiffness of the frame system against lateral translation was calculated as 6000 kN / m. When a harmonic load of F (t) = 80sin20t [kN] was applied to the said structure at the floor level, the impact on the frame was about 400kN at the floor level. Find the weight of the structure W (kN). Choose correct one. A) 54.956 B) 117.720 C) 67.580 D) 86.524
The safe stress, for a hollow column carries an axial load of 2.1 × 103kN is 125MPa. If theexternal diameter of the column is 30 cm, determine the internal diameter.
The simple beam carries a concentrated load P = 15kN. Dimension a and b are 2.5m and 1.2m. respectively. What is the required section modulus of the beam, in mm^3, if the stress is 120Mpa?
A 1.25-in.-diameter solid circular shaft is made of a material that is assumed to be elastoplastic with τY = 18 ksi and G = 11.2 × 106 psi. For an 8-ft length of the shaft, determine the maximum shearing stress and the angle of twist caused by a 7.5-kip·in. torque.
A floor slab 100 mm thick is cast monollthically with beams 250 mm wide 450 mm deepspaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports asuperimposed service dead load of 1.0 kPa and service live load of 2.1 kPa. Using f.=21MPa, long bar f, = 415 MPa, calculate the following:Factored uniform load on a typical interior beam in kN/m using load factors of 1.2for dead load and 1.6 for live load.A. 8.928B. 11.448C. 11.028D. 9.960Effective flange width of a typical interior beam in mm.A. 1,500B. 1.850C. 1.200D. 1.466Required amount of 16-mm-flexure bars for a typical interior beam in positivebending. Use 10-mm-dia. stirrupsA. 512 mm2B. 246 mm2C. 331 mm2D. 427 mm2
For the W410x100 steel beam shown below, the distributed load along AB is a= 6 kN/m, the concentrated load at Point C is b = 12 kN. Apply the average web shear approach to calculate the maximum magnitude of shear stress developed on the cross section at the middle of BC:__ MPa. Calculate your answer to 1 decimal place.
SITUATION 3. A vertical load of W is supported by the tripod shown.a. Which of the following is the most stressed leg(s)?b. If the capacity of each leg is 25 kn, what is the safe valueof W?c. Determine the axial force on leg AD if the maximum safevalue of W is applied.