Answered: SITUATION. A truss is loaded and…

SITUATION. A truss is loaded and supported as shown below. It is carrying a vertical point load at joint F. Determine the axial force of member CD. B D 0.75m 0.75m A 0.5m E 0.5m FL 100 N 0.5m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: What are the functions of structural engineering and what are their outputs?

A: Functions of structural engineering. Structural engineering is an important field of civil…

Q: Question 1 of 8 5F Determine the number of 6meters - 12mm. steel bars required if there are 10…

A: Since the spacing between the bars are not given then from the drawing, number of bars are counted.…

Q: (a) how that the polar radius of gyration ko of the annular area shown is approximately equal to the…

A: Need to find Percentage Error = PE

Q: Determine the forces in all members using method of joil 9. B 5m D 5 m A 30 kN 5 m 5 m 5 m 20 kN 5 m…

A: To find force in all members of the truss

Q: A beam has a width of 300mm and effective depth of 540mm, d' = 60mm. It is reinforced with 4-25mm…

A: fc = 25 MPa (assuming) fy = 420MPa (assuming) d = 540mm b = 300mm d' = 60mm (effective cover)…

Q: water resources engineering about? What are its functions and outputs?

A: Water Resources Engineering is a domain of Civil Engineering where the main focus is on the abundant…

Q: For the below truss system and loading: Complete an approximate analysis assuming the diagonals are…

Q: A water turbine of inertia ?=500 kg.m2 is mounted on a two steel shafts as shown in Fig. 2. If each…

Q: A beam having a span of AB equal to 9m has an overhang of BC equal to 2m. It carries a uniform load…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: 30° 90° 12 m C 1kN 90° 12 m 90° E 1kN 90° 2kN 30% 12 m 90° 1kN

A: Calculate reaction forces in all members by using method of joint.

Q: ensity of 7840 kg/m³ and a ma 1 compression or elongation o fully submerged in the water

A: Given:- m=20kg density =7840kg/m2 m=30kg To find:- total compression or elongation

Q: Illustrate a simple drawing plan of a retaining wall and give measurements

A: Retaining walls are rigid walls which are used for supporting lateral soil load. It is designed to…

Q: 1. A baseball pitching machine "throws" baseballs with a horizontal velocity v0. Knowing that height…

Q: carry using factor of sa

Q: 10 in Problems 4.54-4.55 = The bar has a solid circular cross section. Its polar moment of inertia…

A: Answer We can make use of general equation of angle of twist for varying cross section which is…

Q: A staggered connection is shown in the figure. Using LRFD & ASD, determine the maximum tensile force…

Q: 2.) A 1060kN cube (3m each side) floats in a 1.8m depth of water which is on top of mercury layer.…

A: Size of cube and weight is given

Q: Design bending moment at mid span (+ve) for interior span of a continuous beam with a super-imposed…

A: given- super imposed UDL load=18 kN/mdead load=4 kN/mspan=5m

Q: Q.17 In an oedometer test initial depth of the soil sample is 19 mm and the reduction in depth is…

A: given- intial depth of the soil sample=19 mmreduction in depth=2.1 mmfinal void ratio=0.62

Q: Determine the specific gravity of soil solids based on the data below: Initial volume of soil in…

Q: A 18-m thick soil has a water table 5m below the ground surface. The soil has a void ratio of 0.59…

A: GIVEN DATA void ratio, e=0.59 specific gravity, G=2.69 Degree of saturation, S=47.05%=0.4705 Angle…

Q: Assume h=1.8 sec/veh. Pedestrian demand for all approaches is 120 per hour, pedestrian speed is 4…

A: Given: The critical lane volume is 120 per hour. The saturation volume for phase 1 is 2105 and 300…

Q: How do you think the technology improved construction?

A: Technology in construction means survey equipments( autolevel, total station etc) , construction…

Q: 1. The truck is moving along a 20 m span of beam. The front axle is 30 kN, the middle is 75 kN an…

A: P1 = 45KN P2 = 75KN P3 = 30KN

Q: 18.4 19.3 Mass of empty can, g Mass of empty can + wet soil 51.6 45.6 sample, g Mass of empty can +…

Q: Determine the forces in members CD, CJ, and DJ.

Q: A prestressed concrete pile, 475 mm in diameter, is to be driven in a clayey soil. The pile has a…

A: NOTE :- Since, it is not given the type of pile so taking it as both end bearing and friction pile.…

Q: 250 lb A. 150 lb/ft B 250 lb

Q: A soil sample weighing 256 g is removed from a test pit. Water weighing 128 g will just fill the…

A: step 1-

Q: rectangular foundation is 3 m x 4m in plan is acted upon by a inclined force of 50 kN at an angle of…

Q: No. 3. A simply supported wood beam of rectangular cross section and span length, L = 1.2 m carries…

A: UDL on beam q = Area x Specific weight of beam =(0.14×0.24)×5.4…

Q: 2-123. The container of water has a mass of 20 kg. Block B has a density of 7840 kg/m³ and a mass of…

A: Given:- The mass of the container of water = 20 kg The density of the block B = 7840 kg/m3 The mass…

Q: porosity of a soil having a void

A: Given that Voidratio e = 0.907 Porosity n = ?

Q: Determine the resultant of the forces exerted at point B if the tension in each cable is 450 N. 2m…

A: Express each force as Cartesian vector. Then sum up the two Cartesian vectors to obtain the…

Q: Problem B Equipment Estimating Use the following information for a scraper. Actual cost (delivered)…

A: Total useful life = 6 years at 1400 hrs per year = 8400 hrs Oil Change or lubrication schedule=…

Q: 50. What should be the height (m) of a lighthouse, so that it can be visible from a distance of 3…

Q: H₁ H₂ H₂ Layer 1: Sand Layer 2: Clay D₂ GWT

Q: Determine the forces in all members using method of joints. 7. 1kN 2kN 1kN 90° 300 12 m C 12 m 90°…

A: Determine the forces in all the members of given truss.

Q: What is the psychological widening of a pavement on horizontal curve of radius 230m for ruling speed…

A: given-velocity V=80 kmphRadius of curve R=230 m

Q: 23: Draw shear force and bending moment diagrams by using equation method. 4 kN/m 2 kN/m ·6 mm * -6…

A: GIVEN: TO CALCULATE: Shear force and Bending moment diagram

Q: A soil with a liquidity index of 0.184 has a liquid limit of 56% and a plasticity index of 37%.…

Q: clay layer having a thickness of 10.83 m. has an initial void ratio of 1.14. It is compressed and…

Q: Determine the forces in all members using method of joints. 6. 100 lb 200 lb 100 lb D B 20' 200 lb…

Q: the

A: a simple work plan of a weir and label the parts

Q: 3. In an artesian aquifer, the drawdown is 7.4m at a radial distance of 11m from a well after two…

Q: For the given properties of the beam below, determine the safest wy that the beam will carry. bf =…

A: fc = 34.5MPa fy = 400MPa

Q: The soil profile for a future building construction site is shown in the following figure. The…

A: Given,

Q: 50. What should be the height (m) of a lighthouse, so that it can be visible from a distance of 3…

Q: 3) A rural arterial is expected to carry an ESAL of 1.88x10" during the 1st year of operation with…

Q: A compound circular curve has: R₁ = 500m, R₂ = 750m, A₁ = 38° 20', A2 = 41° 30′ St. P.I = (28+50)…

Concept explainers

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land. Zoning is done or can be understood with the help of a site plan.

Question

PLEASE ANSWER ASAP THANKS

SITUATION. A truss is loaded and supported as shown below. It is carrying a vertical point load at
joint F.
Determine the axial force of member CD.
B
0.75m
0.75m
O54.21
66.67
71.92
29.0
A
0.5m
E
0.5m
F
100 N
0.5m
C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 select the section

VIEW

Step 2 force in CD

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two forces act on the screw eye. If F1 = 400 N andF2 = 600 N, determine the angle θ (0° ≤ θ ≤ 180°) betweenthem, so that the resultant force has a magnitude ofFR = 800 N.
A force F = (0.5i – 2.0j + 7.0k) kN acting at A(5, -4, 0)m about axis BC where B(6, 8, 4)m and C(-6, -5, 8)m. What is the perpendicular distance between F and the axis BC in meters?
What is the general moment equation? Section the beam at the rightmost segment of the beam. El = 75,000 kN∙m2
The 300N block rests upon a level plane for which the fk is 0.20. A force P = 100N, directed at 30° from the horizontal pulls the block and moves 80m starting from rest. If the 100N force is then removed, how much further will it travel?
Draw the shear and moment curves for the beamin Figure P5.35. Reaction at support B is given. Locateall points of zero shear and moment. Sketch the deflectedshape.
For the beam and loading shown below (L = 2.4 m, E = 200 GPa, I = 1000 mm4 and w = 30 kN/m), find (a) TThe slope at point D.(b) The reaction force at end A
7. The Bearing line AB is N 55o44’ E and the bearing of the next line BC is N 25o 12’ W. Compute the deflection at point B
The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques shown. A 44-mm-diameter hole has been drilled into portion CD of the shaft. The entire shaft is made of steel for which G = 77 GPa. 4. Calculate the angle of twist of point A relative to point D in degrees.
Consider the beam in Figure P9.21 without theapplied load and support settlement. Compute the reac-tions and draw the shear and moment curves for the beamif support A rotates clockwise by 0.005 rad.
Write the equations for shear and moment be- tween points B and C for the rigid frame in Figure P5.11. Select the origin at point
(a) Draw the shear and moment curves for theframe in Figure P5.40. Sketch the deflected shape.(b) Write the equations for shear and moment in columnAB. Take the origin at A. (c) Write the shear and momentequations for girder BC. Take the origin at joint B.
For Beam 4, what is the vertical reaction at A?