SITUATION. An 8-m long ladder weighing 900 N is shown in the figure. It is required to determine the horizontal force P that must be exerted at point C to prevent the ladder from sliding. The coefficient of friction between the ladder and the surface at A and B is 0.20. BN W = 900 N %3D 4m 4.59m 2 m 35° A, AN 6.55m Determine the required force P. B.

SITUATION. An 8-m long ladder weighing 900 N is shown in the figure. It is required to determine the horizontal force P that must be exerted at point C to prevent the ladder from sliding. The coefficient of friction between the ladder and the surface at A and B is 0.20. BN W = 900 N %3D 4m 4.59m 2 m 35° A, AN 6.55m Determine the required force P. B.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter15: Slope Stability

Section: Chapter Questions

Problem 15.21P

See similar textbooks

Similar questions

Knowing that L = 4 m, Concentrated load P = 15 kN and uniform distributed load w = 12 kN/m, determine the slope at C by Castigliano’s Theorem.(E= 200 GPa, I = 40x106 mm4)
If mu = 0.30 under both blocks and A weighs 400 lb, find the maximum weight of B that can be started up the incline by applying to A a rightward force P of 500 lb.
22 A 220-kg block is resting on a 56 deg inclined plane with a coefficient of friction = 0.76. Find the required horizontal force P (kN) that is necessary to prevent motion DOWN the incline. ROUND OFF TO TWO DECIMAL PLACES.
A 6m long ladder weighing 74.41 kg is shown in the figure below. A horizontal force P is requires at point C to prevent the ladder from sliding. The coefficient if friction between surfaces is 0.15 Determine the required force P Choices: 609 N, 506 N, 647 N, 640N
A Block weighing 100N is held on a 400 incline by a Bar attached to a 150N Block on a horizontal plane. The Bar which is fastened by a smooth pin at each end is inclined 200 above the horizontal. The angle of Friction between each Block and its Plane is 180. Find the horizontal Force P applied to the150N Block which will cause it to be on the point of moving to the right?
A uniform ladder 5 m long and weighing 80N rests against on a vertical wall at B and one end at A (on the ground.) The angle friction at all contact surfaces is 21.8°. Fiind the smallest angle at which ladder can be inclined with the horizontal before it is on its verge of slipping.
Two blocks A and B have a weight of 11 lb and 5 lb , respectively. They are resting on the incline for which the coefficients of static friction are μA = 0.16 and μB = 0.25. Determine the angle θ which will cause motion of one of the blocks. What is the friction force under each of the blocks when this occurs? The spring has a stiffness of k = 2 lb/ft and is originally unstretched. Determine the smallest angle and determine the friction force under block A and B under this angle.
A cylinder weighing 400 lb is held against a smooth incline by means of the weightless rod AB in FIig. P-309. Determine the forces P and N exerted on the cylinder by the rod and the incline respectively.
6. A simply supported beam carries a concentrated load of 24 kN at 6 meters from the left support (1 meters from the right support). Use EI = 80,000 kN-m2. Solve for the slope at the left support in degrees. ROUND OFF TO FIVE DECIMAL PLACES.
Find the following: - Righting Moment - Overturning Moment - Factor of Safety Against Sliding - Factor of Safety Again Overturning Given: μ = 0.6 γ = 23.50 kN/m^3 b1 = 1.60 m b2 = 4.00 m h1 = 10.00 m h2 = 8.00 m
3. The body on the incline is subjected to the vertical and horizontal forces shown. Find the components of each force along X-Y axes oriented parallel and perpendicular to the incline.
Slope deflection method: compute for shear and momemt diagram