SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b I Bronze: A 1200 mm E83 GPa L-2.0m What is the value of P Steel: A 900 mm E 200 GPa L=1.5m

SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b I Bronze: A 1200 mm E83 GPa L-2.0m What is the value of P Steel: A 900 mm E 200 GPa L=1.5m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A rigid beam rest on two bronze bars 700mm long. Another aluminum bar is placed between them which is 699.93mm long. If the weight of the beam is 375KN, determine the stress in the aluminum bar in MPa. (Round your answer to 3 decimal places) (Exclude your unit in the answer box)
Considering the steel rod at E, how long will its elongation be if it is hollow with an outside diameter of 25 mm and a thickness of 1.5 mm? Use E=200 GPa
The rods A and B having a tensile stress of 400 N/mm², determine the diameter so that they can support the load shown. Then calculate the change in length and strain in each bar if (E=200000 MPa) (L=2 m)
A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress developed in the rod, in kN/m^2. Is the tensile or compressive? (b) compute the amount of elongation (in mm) in the steel rod caused by the applied load, (c) what will be the elongation (in mm) in the steel rod if the weight of the steel rod is included? Use density of the steel to be 7860 kg/m^3. Young's modulus of elasticity, E=200GPa. W=mg. Draw free body diagram of the steel rod.
The structure shown below consists of a brass core inserted into a steel tube of cross sectionsquare. If a moment of 8 kN × m is applied at its end, determine the maximum bending stress in thebar. E (brass) = 100 GPa, E (steel) = 200 GPa.
The beam shown in the figure below has the following properties:28-ft simple span f'c = 4000 psi fr = (7.5)(Square root of f prime X c) reinforced concrete weight = 150 lb/ft3 Solve for : 1.) The total area of the section in in2 2.) The gross moment of inertia in in4 3.) The cracking moment in kp-ft 4.) The self weight of the beam in kp/ft 5.) The superimposed uniform load that will cause the beam to crack in k/ft
two rods attached to a rigid bar AB with negligible mass . A 101 kN load was applied at the end of this bar. The computed stresses for steel and bronze are Blank 1 mPa and Blank 2 mPa respectively.
Answer all.a.A mild steel flat of width b= 150 mm, thickness t = 20 mm and length L= 6000 mm carries an axial pull P = 300 kN. If modulus of elasticity of mild steel is 200 GPa and Poisson’s ratio is 0.25, calculate the change in length, width and thickness of the flat. B.A stepped bar made of brass is subjected to axial loads as shown in the below figure. Determine the total change in length of the bar. Take E =100 GPa.figure is attached C.A thin cylinder of external diameter 820 mm, length 3 m and wall thickness of 10 mm is subjected to an internal pressure of 2.5 N/mm2 . Determine the change in diameter and length. Take Young’s modulus = 2×105 N/mm2 and Poisson’s ratio = 0.25.
3B. A stepped bar made of brass is subjected to axial loads as shown in the below figure. Determine the total change in length of the bar. Take E =100 GPa.
The rectangular steel plate in the figure is forced by the forces given at the A and B points. a) Size the cross section according to the most economical section ratio a / b = 1/2. b) Calculate the amount of deformation occurring in the rod in this case. The yield stress of the steel plate can be taken as 400 Mpa, the modulus of elasticity 2.10 ^ 5 Mpa, the safety coefficient of the design can be taken as 2. F = 3kN L = 1.5m
A steel bar of rectangular cross section 45 mm (height) x 60mm (base) and pinned at each end is subject to axial compression. The proportional limit of the material is 320 Mpa and E= 200 GPa. -Find least Radius of Gyration (in mm)? -Determine the transition length (in mm) in which the Parabolic formula may be used instead of the Euler's equation.? -Determine the transition slenderness ratio in which the Parabolic formula may be used instead of the Euler's equation.? -If the Length is 1 meter, determine the critical load (in KN) using pin support. -if the length is 3 meters, determine the critical stressn(in MPa) using pin support.