SITUATION. The laminated beam, shown in cross section, is composed of five 6-in. by 2- in planks that are glued togetther. The beam caries a uniformly distributed load of intensity wo over its 8-t simply supported span. The working stresses are 80 psi for shear in glue, 110 psi for shear in wood, and 1100 psi for bending in wood. O Zoom image Determine the maximum allowable load wo (kip/ft) for the shear in wood. O 12 13.75 O 10 se2 in. 10 in.

SITUATION. The laminated beam, shown in cross section, is composed of five 6-in. by 2- in planks that are glued togetther. The beam caries a uniformly distributed load of intensity wo over its 8-t simply supported span. The working stresses are 80 psi for shear in glue, 110 psi for shear in wood, and 1100 psi for bending in wood. O Zoom image Determine the maximum allowable load wo (kip/ft) for the shear in wood. O 12 13.75 O 10 se2 in. 10 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

calculate the nominal shear strength(kN) of 4-legged stirrups 12 mm diameter, spaced at 280 mm on centers fo a beam with effective depth of 417 mm. use yield strength of stirrup fy = 275 Mpa.
A 6.96.9 mm long simply supported wood beam carries a uniformly distributed load of 10.810.8 kN/mkN/m, as shown in Figure A. The cross-sectional dimensions of the beam as shown in Figure B are b=195b=195 mmmm, d=490d=490 mmmm, yH=80yH=80 mmmm, and yK=158yK=158 mmmm. Section a–a is located at x=1.4x=1.4 mm from B. (a) At section a–a, determine the magnitude of the shear stress in the beam at point H. (b) At section a–a, determine the magnitude of the shear stress in the beam at point K. (c) If the allowable shear stress for the wood is 950950 kPakPa, what is the largest distributed load ww that can be supported by the beam?
A reinforced concrete rectangular beam has a width of 315mm and an effective depth of 525mm. The beam is reinforced with six 25mm diameter tension bars. Take fy=400MPa and fc=29.50MPa. What is the nominal moment capacity of the beam, kN-m? What is the balanced steel area, mm2?
6 Calculate the nominal shear strength (kN) of 4-legged stirrups 12-mm-diameter, spaced at 280 mm on centers for a beam with effective depth of 417 mm. Use yield strength of stirrups fy = 275 MPa.
A rectangular, tied column 480 mm wide along x-axis and 540 mm wide along y-axis is reinforced with 4 25-mm-diameter vertical bars with fy = 420 MPa enclosed in 10-mm-dia. ties. Using f'c = 21 MPa, calculate the nominal axial strength at balanced condition in kN with bending about the x axis. Write your answer with 2 decimal places only.
6 Calculate the nominal shear strength (kN) of 4-legged stirrups 10-mm- diameter, spaced at 210 mm on centers for a beam with effective depth of 470 mm. Use yield strength of stirrups fy = 275 MPa.
Calculate the nominal shear strength (kN) of 4 - legged stirrups 12 - mm - diameter, spaced at 230 mm on centers for a beam with effective depth of 418 mm. Use yield strength of stirrups fy = 275 MPa.
The overhanging beam shown supports the given ultimate load Wu= 5okN/m. The section is 300mm by 500mm rectangular beam having f'c=35MPa, fy=420 MPa, stirrups diameter = 10mm and concrete cover 40mm. a.) the area of steel reinforcement corresponding to rho max in mm2.b.) the location of the point of zero shear in the beam measured from the left support B in mm.c.) Calculate the maximum positive moment in the beam in kN.m.d.) Calculate the required reinforcement Asreqd corresponding to the maximum positive moment in mm2.e.) Calculate the depth of the compression block of the final positive moment section in mm.f.) Calculate the depth of the neutral axis of the final positive moment section in mm.g.) What is the ultimate moment capacity of the final positive moment section in kN.m.h.) Calculate the additional positive moment that can be imposed to the beam without exceeding the moment capacity of the final positive moment section in kN.m.
An I-beam whose flange width is 375 mm, flange thickness is 15 mm, web thickness is 20 mm, total depth of 450 mm, and Fy of 248 MPa is to be used to carry a uniform load all throughout its length, 3m. a. What is the allowable bending stress? b. What is the maximum safe uniform load that the beam could carry? c. Determine the moment of inertia of the section.
A reinforced concrete T-beam with d= 550mm, bw=300mm, slab thickness=100 mm is 4.8m long and spaced 3m on centers. The beam supports a service dead load moment of 400kN.m (including its weight) and a service live load moment of 500kN.m. If fc'=27.5MPa, fy = 414MPa, determine the required steel area.A. 6882 sq.mmB. 6828 sq.mmC. 6288 sq.mmD. 8682 sq.mm
PLEASE WRITE WITH DETAILED SOLUTION A reinforced concrete T-beam has an effective depth of 650mm and is reinforced with 8D25mm dia. Bars. The web width is 330mm and has aflange thickness of 115mm. The beam has a span of 8m and has a spacing center to center equal to 4m. fc’=21MPa and fy=350MPa. Compute the effective width of the flange and the nominal moment capacity of the beam.
Draw the S.F. and B.M. diagrams for the overhanging beam carrying uniformly distributed load of 30kN/m over the entire length and a point load of (Your roll no.kN) as shown in figure. Locate the point of contraflexure.