Solve a 100 x 100 x 10mm angle is to be welded to a gusset plate shown. The angle carries a load of 185 kN applied along its centroidal axis. The maximum size of filllet weld that can be used in 8mm and the allowable shear stress of 94 MPa. Determine the lengths of the side fillet welds if a transverse fillet weld is added at the end of the angle. 71 mm 185 kN 29 mm

Solve a 100 x 100 x 10mm angle is to be welded to a gusset plate shown. The angle carries a load of 185 kN applied along its centroidal axis. The maximum size of filllet weld that can be used in 8mm and the allowable shear stress of 94 MPa. Determine the lengths of the side fillet welds if a transverse fillet weld is added at the end of the angle. 71 mm 185 kN 29 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.4.7P: Use an elastic analysis and compute the extra load in the weld (in kips per inch of length) caused...

See similar textbooks

Similar questions

Use an elastic analysis and compute the extra load in the weld (in kips per inch of length) caused by the eccentricity.
The double T-beam is fabricated by welding the three plates together as shown. Part A Determine the shear stress in the weld necessary to support a shear force of V=78 kN�=78 kN.
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 48 in. and a wall thickness of 0.375 in. Determine the largest allowable gage pressure if the allowable normal stress perpendicular to the weld is 26 ksi.
Use an elastic analysis and determine the maximum load in the weld (in kips per inch of length).
The vertical member shown in Figure STCN17.02 consist of two angles welded to the 8-mm thick gusset plate. Given the following data: Angle size: 75 mm x 50 mm x 6 mm (long legs back-to-back) Area of one angle = 738 mm Size of weld = 6 mm Yield strength of steel, Fy = 248 MPa Allowable weld shear stress, F, = 124 MPa a = 25 mm a. Determine the safe capacity of the vertical member in kN. b. If P= 185 kN, determine the length of weld L2 (mm) such that each weld have equal shear stress. Neglect end returns. c. If L1 = 140 mm and L2 = 70 mm, determine the safe load P (kN) based on weld capacity assuming all welds have equal stress. AP L1 L2
Find the Load Capacity of the weld if the throat thickness is 8. 13 mm, Nominal Tensile Strength, Fu = 520 MPa, and length of weld = 400 mm.
Q1/ A bracket is welded to a frame by two 10 mm fillet welds as shown in Fig., carries a load of 9 kN. Find maximum shear stress in the welds, assuming each weld to be 57 mm long and parallel to the axis of the angle. All dimensions in mm.
One leg of an 8 x 8 x 3/4 angle is to be connected with side welds and a weld at the end of the angle to a plate behind, to develop the loads PD = 170 k and PL = 200 k. Balance the fillet welds around the center of gravity of the angle. Using LRFD and ASD methods, determine weld lengths if E70 electrodes and maximum weld size is used.
A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu = 483.33 MPa. Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. Determine the length of side fillet weld required at the heel. Determine the length of side fillet weld required at the toe.
A hanger is suspended from a plate that is welded to a wide flange beam as shown. The plate requires a 1”x1” chamfer in the inside corners to clear the fillet radius of the beam. A ¼ inch double sided fillet weld is used with no welds placed at 1”x1” from the inside corners as shown in the weld configuration. Determine the maximum load the hanger can carry using ASD and the Elastic method if the eccentricityof the load from beam centerline is 7”.
For the clevis connection shown, determine the shear stress in the 20-mm-diameter bolt for an applied load of P = 130 kN.
Assuming the thickness of the weld is 1 mm, calculate: 1.Moment of Inertia of every parts of weld sections 2.Global Centroid for the weld, assuming it is angle section. 3.Global Moment of Inertia with respect to Y and X axis respectively (Ix and Iy) . 4.The farthest distance of weld, Rmax. of weld subject to in-plane