Solve the following neatly: Determine the average velocity for water flow in the following situations: a. a 2.50-in inside diameter pipe carrying a water at a volumetric flow rate of 50 gpm. * 197.4 ft/min * 3.29 ft/s * 39.22 in/s * none of the above b. a 20 mm inside diameter pipe carrying water at a volumetric flow rate of 50 L/min. * 2.65 m/s * 2750 mm/s * 2.55 m/s *none of the above

Solve the following neatly: Determine the average velocity for water flow in the following situations: a. a 2.50-in inside diameter pipe carrying a water at a volumetric flow rate of 50 gpm. * 197.4 ft/min * 3.29 ft/s * 39.22 in/s * none of the above b. a 20 mm inside diameter pipe carrying water at a volumetric flow rate of 50 L/min. * 2.65 m/s * 2750 mm/s * 2.55 m/s *none of the above

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water enters a cylindrical tank through two pipes at rates of 0.223 ft3/s and 0.557 ft3/s (see figure below – control volume is indicated by dotted lines). (a) Indicate if the flow is steady or unsteady. (b) Calculate the average velocity (in ft/s) of the flow leaving the tank through an 8-in inside diameter pipe if the level of the water in the tank remains constant.
With a coefficient of friction equal to 0.019, what diameter of pipe is required to carry a flow of 17cubic meters per minute considering a headloss of 2 m per kilometer?580 mm380 mm480 mm680 mm
Calculate the values of critical height and critical velocity for water flowing through a rectangular channel of width 5 m when the flow rate is 15 m3/sec.
Determine whether the flow is turbulent or laminar if a fluid flows at 0.001?^3/? through a 100mm diameter pipe.
water is flowing into a conical vessel 21 cm deep and 13 cm across the top. if the rate at which the water surface is risingis 2.6 cm/sec, how fast is the water flowing into the conical vessel when the depth of water is 9 cm?
The discharge of water in a 25 cm diameter pipe is 0.05 m3/s. What is the mean velocity?
Fluid Mechanics Question An empirical equation for the velocity distribution in a horizontal, rectangular, open channel is given by u= umax(y/d)n where u is the velocity at a distance y feet above the floor of the channel. If the depth of flow is 1.2m, umax=3m/s, and n=1/6, what is the discharge in cubic meters per second per meter of width of the channel? What is the mean velocity?
Water flows smoothly over a small bump in a channel of constant width, as shown in Figure P10.11. At any cross-section the velocity may be considered constant over the entire area. If V1 is the velocity at entry, where the depth is Y1, and V2 is the velocity where the bump has its highest point, where the depth is Y2. If Y1/Y2 = 1.8, find (a) The Froude number of the flow at entry. (b) The Froude number at the top of the bump.
The flow from A to E is 0.280 cum/sec. Using n = 0.09 Pipe 1 (Diameter and Length): 450 mm, 300 m Pipe 2 (Diameter and Length): 250 mm, 360 m Pipe 3 (Diameter and Length): 350 mm, 300 m Pipe 4 (Diameter and Length): 300 mm, 1200 m Pipe 5 (Diameter and Length): 200 mm, 600 m Pipe 6 (Diameter and Length): 450 mm, 600 m Compute the Total head loss from A to D in meters Round your answer to 3 decimal places.
A pipe line consists of successive lengths of 406-mm, 367-mm, and 298-mm pipe. With a continuous flow through the line of 478 Lit/sec of water, compute the mean velocity in 367 size of pipe. (m/s) Round your answer to 2 decimal places.
Consider the piping system shown . The average speed of water flowing through the 600-mm-diameter section of the piping system is 5 m/s. What is the volume flow rate of water in the piping system? Express the volume flow rate in L/s. For the case of steady flow of water through the piping system, what is the average speed of water in the 300-mm-diameter section of the system?
Three pipes of lengths 800 m, 600 m and 300 m and of diameters 400 mm, 300 mm and 200 mm, respectively, are connected in series. The ends of the compound pipe are connected to two tanks, whose water surface levels are maintained at a difference of 15 m. Determine the rate of flow of water through the pipes if f= 0.005. What will be diameter of a single pipe length 1700 m and f = 0.005, which replaces the three pipes?