Solve the following. Show complete solution, resistorcombination and circuit transformation. Box final answer. Fixcalculator to 3 decimal places.• 1. Determine the value of R, for maximum power transfer. Also,determine the maximum power.180V( ±30n) 3ARL

Answered: Image /qna-images/answer/778b166c-f14c-48e6-8585-58c66c414038.jpg

Answered: Solve the following. Show complete…

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter20: Special-purpose Outlets For Ranges, Counter-mounted Cooking Unit , And Wall-mounted Oven

Section20.2: Wall-mounted Oven Circuit And Free-standing Range

Problem 11R

See similar textbooks

Similar questions

Analyze the circuit of Figure 1 by using Nodal analysis to calculate the voltage at each node (??, ??, ?? and ??) (At each step write the formulas then substitute with the values). Please clean handwriting
Voltage Drop! Assume that you were tasked to install a microwave oven using 12 AWG copper. When you look at the spec plate for the oven, you discover that the oven is rated for 240V, 60HZ, and takes a current of 25A. The location for the oven is 785.7 Ft, away from the breaker panel. Calculate the expected VD if any. Assume temperature to be 75 ̊ C. what is the Voltage Drop ? Answer?
Please show a complete step-by-step solution. Thank youGive your final answers in at least 2 decimal places - make it 3 or 4 decimal places whenever required in the problem. If you are doing a step by step calculation, maintain 6 decimal places in your in-between calculations to hit good accuracy in your final answers. Use 1 hp = 746 Watts in your conversion whenever necessary. A 110-hp, three-phase, wye-connected, 50-Hz, 460-V, four-pole, cylindrical-rotor synchronous motor is operating at rated conditions and 88 percent power-factor leading. The efficiency, excluding field and stator losses, is 95 percent, and the synchronous reactance is 2.81 Ohms/phase. Determine the developed torque in lb-ft. Give your final answer in 2 decimal places. Correct Answer: 405.42 ± 0.01
Please show a complete step-by-step solution. Thank youGive your final answers in at least 2 decimal places - make it 3 or 4 decimal places whenever required in the problem. If you are doing a step by step calculation, maintain 6 decimal places in your in-between calculations to hit good accuracy in your final answers. Use 1 hp = 746 Watts in your conversion whenever necessary. A 110-hp, three-phase, wye-connected, 50-Hz, 450-V, four-pole, cylindrical-rotor synchronous motor is operating at rated conditions and 85 percent power-factor leading. The efficiency, excluding field and stator losses, is 95 percent, and the synchronous reactance is 3.82 Ohms/phase. Determine the magnitude of the excitation voltage in volts. Give your final answer in 2 decimal places. Correct Answer: 672.23 ± 0.01
Please show a complete step-by-step solution. Thank youGive your final answers in at least 2 decimal places - make it 3 or 4 decimal places whenever required in the problem. If you are doing a step by step calculation, maintain 6 decimal places in your in-between calculations to hit good accuracy in your final answers. Use 1 hp = 746 Watts in your conversion whenever necessary. A 130-hp, three-phase, wye-connected, 50-Hz, 440-V, four-pole, cylindrical-rotor synchronous motor is operating at rated conditions and 86 percent power-factor leading. The efficiency, excluding field and stator losses, is 90 percent, and the synchronous reactance is 2.13 Ohms/phase. Determine the pull-out torque of the motor in lb-ft. Give your final answer in 2 decimal places. Correct Answer: 885.36 ± 0.01
Given a circuit below, calculate the admittance in millisiemens when R = 20 ohms, XL = 13 ohms, and XC = 38 ohms. Round off the answer to 4 decimal places.
The disconnecting means for the motor-operated appliances such as the fuel-fired furnace discussed in this chapter is required to comply with NEC ______. a. 725.136(A)b. 422.31(C)c. 422.60d. 725.179(G)
answer number 5 asapppppo
Question (1): With proper example and circuit diagram briefly explain the following theorems. (i) Millman’s theorem(ii) Miller’s theorem Here is one question with two subparts. Provide complete question answer.
Answer number 11 and show a clear and readable solution. Circuit Diagram is given below. Thanks!!!
How to draw a Series-Parallel Circuit with one switch controlling two electric heaters, each being supplied with line voltage? Also, I still need help understanding these Series-Parallel Circuits. Thank You Very Much in advance.
#17 hello can you find , ir1, ir2 ir3 rt, it ,and pt . Thank you please show me how to do my homework

SEE MORE QUESTIONS

Recommended textbooks for you

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Solve the following. Show complete solution, resistor combination and circuit transformation. Box final answer. Fix calculator to 3 decimal places. • 1. Determine the value of R, for maximum power transfer. Also, determine the maximum power. 30n )3A ЗА RL