Statement for Lin An inductor designed with 400 turns coil wound on an iron core of 16 cm² cross sectional area and with a cut of an air gap length of 1 mm. The coil is connected to a 230 V, 50 Hz ac supply. Neglect coil resistance, core loss, iron reluctance and leakage inductance.(µo = 4TX10 H/m) Q.76 The current in the inductor is

Statement for Lin An inductor designed with 400 turns coil wound on an iron core of 16 cm² cross sectional area and with a cut of an air gap length of 1 mm. The coil is connected to a 230 V, 50 Hz ac supply. Neglect coil resistance, core loss, iron reluctance and leakage inductance.(µo = 4TX10 H/m) Q.76 The current in the inductor is

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A ceramic capacitor is to be constructed to have a capacitance of 0.01µF and to have a steady working potential of 2.5 kV maximum. Allowing a safe value of field stress of 10 MV/m, determine (a) the required thickness of the ceramic dielectric, (b) the area of plate required if the relative permittivity of the ceramic is 10, and (c) the maximum energy stored by the capacitor.
5 Assume that you have been tasked with evaluating a new inductor. The inductor has a Q of 1454 at 50KHZ; a 0.1mm diameter, and is fabricated by wrapping a 10meter length copper wire wound around a magnetic core. Assume the following parameters for copper wire wound around a magnetic permeability of copper is 1. A. what is the inductance of the inductor? B. Assuming that the skin affect does not affect the Q at 50KHZ at all, determine the Q at 50MHZ.
Given a two magnetically coupled coils -coils physical structure is P11=P22 -self-inductance of coil 1: 288mH -coefficient of coupling: 0.75 -mutual inductance: 90mH -wound on a nonmagnetic core Determine L2 Blank 1 milli If N1 =1200, what is the value of P2? Blank 2 micro
Given a two magnetically coupled coils -coils physical structure is P11=P22 -self-inductance of coil 1: 288mH -coefficient of coupling: 0.75 -mutual inductance: 90mH -wound on a nonmagnetic core Determine the turns ratio N1/N2 If N1 =1200, what is the value of P1? in micro
A. A coil of 1000 turns is uniformly wound on a ring of non-magnetic material, the mean diameter being 20 cm. The cross-sectional area of the coil is 4 cm2. Determine the selfinductance of the coil. Ans. 0.8mH B.An iron core 0.4m long and 5 cm2. In cross section, is wound with 300 turns. When a current of 0.5 A flows in the coil, how much is the inductance of the coil. Assume the core has a permeability of 2500.
Calculate the gravimetric capacitance of a carbon based electrode with an aqueous electrolyte solution. Assume the surface area of the carbon electrode is 1200 m2/g, and the relative static permittivity of the aqueous electrolyte solution is 80. The permittivity of free space is 8.85 × 10−12 F/m. Indicate any other assumptions you have to make.
Given a two magnetically coupled coils -coils physical structure is P11=P22 -self-inductance of coil 1: 288mH -coefficient of coupling: 0.75 -mutual inductance: 90mH -wound on a nonmagnetic core Determine the turns ratio N1/N2 BLANK If N1 =1200, what is the value of P1? BLANK micro
2. A parallel plate capacitor with a plate area of 0.13 square meters separated by 1 mm is charged to 9 Volts by a battery, which is then disconnected. The plate separation is then increased to 40 mm.A. Using the expression for the capacitance of a parallel plate capacitor, what do you expect the new potential difference across the plates to be after the increase?B. Suppose you measure the potential difference across the plates after the separation and find it to be 30 V (this should be very different from what you found in part A). This unexpected result can be explained by the effects of “stray capacitance” with nearby objects. Assuming that the stray capacitance can be modeled as a capacitor connected in parallel with the parallel plate capacitor, find the value of this stray capacitance.
A capacitor is made from two flat parallel plates placed 2 mm apart, .and its capacitance at vacuum is 10-12- F , if 200 volt applied in between then a Dielectric material was entered and its Dielectric constant Is 49 , Calculate : a) the new value of capacitance after the entrance of the Dielectric b) what is the value of charge on Dielectric material surface c) the polarization p of the Dielectric material d) calculate the displacement and the field inside the Dielectric
A choke coil of resistance 8 ohm and inductance 0.15 H is connected in series with a capacitor of capacitance 125 ?? across a 230-V, 50- Hz supply. Calculate: (a) the inductive reactance, (b) capacitive reactance, (c) impedance, (d) current, (e) voltage across the coil and the capacitor, respectively. (f) phase difference between the current and the supply voltage.
A conducting coil, with current i(t) = 4.40e−0.0250t sin(120πt), with i in amperes and t in seconds, is placed next to a second coil, end to end. At t = 0.720 s, a lab tech measures the emf across the second coil, and the result is −3.50 V. What is the mutual inductance (in mH) of the coils?
A solenoid coil needs to be manufactured which produces an inductance of at least 2000 Gauss (in SI system = Tesla) when a 10mA current flows through the conductor. Due to space limitations, the coil should be composed of 10 turns over a 1cm length. Select a suitable core material for the manufactured solenoid coil from the table. A. MnZn Ferrite B. 4750 alloy C. None of the mentioned/ Geen van die genoemde D. Silicon iron