Steady-state temperatures at selected nodal points of the symmetrical section of a flow channel are known to be 17= 66.67 °C and T8= 50 °C. The wall has a thermal conductivity of k= 10 W/m.K. The outer surface of the channel experiences convection with fluid temperature of To,o= 10 °C and convection coefficient of ho-250 W/m². K. Determine the temperature at node 3. 00,0

Steady-state temperatures at selected nodal points of the symmetrical section of a flow channel are known to be 17= 66.67 °C and T8= 50 °C. The wall has a thermal conductivity of k= 10 W/m.K. The outer surface of the channel experiences convection with fluid temperature of To,o= 10 °C and convection coefficient of ho-250 W/m². K. Determine the temperature at node 3. 00,0

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.16P

See similar textbooks

Similar questions

3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
A mercury thermometer placed in oil well is required to measure temperature of compressed air flowing in a pipe. The well is 150 mm long and is made of steel (k = 50 W/m°C) of mm thickness. The temperature recorded by the well is 150°C while pipe wall temperature is 75°C Heat transfer coefficient between the air and well wall is 50W/m²°C. Estimate true temperature of
Water at 20 C flows in a smooth pipe 0.04 m indiameter at a Reynolds number of 50,000. Thewall temperature is maintained at 25C. The bulk temperature and film temperature are assumed to be at 20C. Using Colburn analogy find the value of heat transfer coefficient. The properties of water are: Density = 999 kg/m3; viscosity = 1 cp; Pr = 6.94; Specific heat 4182 K/kgK; k=0.603 W/mK
A transformer is to be cooled via forced air convection. To increase the effectiveness of thecooling, Alloy 1095 cast aluminum fins are attached to the top of the transformer overwhich air is blown (negligible thermal contact resistance between the transformer and thefins). The fins are 2 cm thick and 7 cm long and span the entire length of the transformer,and the transformer is 7 cm wide and 10 cm long. Air leaves the cooling fan at 25°C .a) Decide how to model the fins before performing any real analysis. Youare willing to accept some error in your analysis and so you will either model thefins as having adiabatic tips or being infinitely long. You expect the average convectioncoefficient over the heat transfer surfaces for this system to be around 50 W m2– K⁄ .Which tip condition should you use for the fins in your analysis? b) Modeling the transformer as being isothermal, determine the average convectioncoefficient over the heat transfer surfaces. Account for heat transfer from the…
150 L/s of hot air at 80 degrees Ceelsius enters an 8m long uninsulated square duct of cross-section 20 cm x 20 cm and leaves at 70 degree Celsius. The outer surface temperature of duct is observed to be constant. Use Colburn Equation.
Write the appropriate Nusselt value for the each set of conditions provided below.1. Forced convection over a flat plate at constant qs. Calculated Re at mean temperature is 3500 and Pr= 0.7154. 2. Natural convection in a small holding tank with a heating element at the bottom. The calculated Ra number is 2.37 x10^93. Forced convection through an elliptical duct at constant Ts, where a/b=8. The temperature of the fluid at the inlet is higher than at the exit. Flow is fully developed with Re = 33370 and Pr= 0.693. 4. Natural convection over a sphere with Ra = 5 x 10^9 and Pr = 0.7362 PS. Do not round off intermediate values
A thick-walled cylindrical tubing of hard rubber (k=0.151 W/m*K) having an inside radius of 5 mm and an outside radius of 20 mm is being used as a temporary cooling coil in a bath. Ice water is flowing rapidly inside, and the inside wall temperature is 275 K. The outside surface temperature is 300 K. A total of 20 W must be removed from the bath by the cooling coil. How many meter of tubing are needed?
Hab. Tiruneh, [4/2/2023 1:23 AM]A solar flux q ^ * falls on a unit length of a very thin tube of diameter d. Inside the tube is a stationary water with initial temperature T_{i} (same as ambient and no gradient inside at any time) and absorbs some of the heat while the rest leaves by convection from the surface to the ambient at T_{m} Develop an equation that can help to determine the temperature of the water at any time. Plot the temperature of the water against time. For a long elapsed time what will be the temperature? To simplify the analysis use theta = T*T_{e} * d*theta = dT theta_{i} = T_{i}*T_{o} (initial condition. Hab. Tiruneh, [4/2/2023 11:53 AM]A flat wall is exposed to an environmental temperature of 38°C. The wall is covered with a layer of insulation 2.5 cm thick whose thermal conductivity is 1.4W / (m ^2 *` C and the temperature of the wall on the inside of the insulation is 315°C. The wall loses heat to the environment by convection. Compute the value of the convection…
2.2: Water at a temperature of T∞= 25°C flows over one ofthe surfaces of a steel wall (AISI 1010) whose temperatureis Ts,1= 40°C and thermal conductivity of steel is 671 w/m.k. The wall is 0.35 m thick, and itsother surface temperature is Ts,2= 100°C. For steadystateconditions what is the convection coefficient associatedwith the water flow?
A thermocouple junction is in the form of 8 mm diameter sphere. Properties of materialare: Cp = 420 J/kg-K; ρ = 8000 kg/m3 ; k = 40 W/m-K; h = 40 W/m2 -K. This junction isinitially at 40 oC and inserted in a stream of hot air at 300 oC. Find the following:a. Time constant of the thermocouple.b. The thermocouple is taken out from the hot air after 10 seconds and kept in still airat 30 oC. Assuming the heat transfer coefficient in air is 10 W/m2-oC, find thetemperature attained by the junction 20 seconds after removal from hot air.
Water flows in a duct having a cross-section of 10x20 mm with a mean bulk diameter of 15.56 deg C. If the duct wall temperature is constant at 60 deg C and fully developed laminar flow prevails. a.) Calculate the heat transfer coefficient, h in W/m2-deg Cchoices: (405, 305, 151, 252) b.) What is the thermal conductivity of water at the given temperature, k in W/m-deg Cchoices: (0.604, 0.6, 0.585, 0.595) c.) Calculate the heat transfer rate per unit length in W/mchoices; (605, 366, 505, 404)
Air (pressure 1 atm) enters a circular pipe 5 cm in diameter at 20 °C with an average speed of 5 m/s. The tube wall is maintained at a constant surface temperature of 160°C, and the mean outlet temperature is 80°C. Estimate the length of the tube. Mainly, I also need the solution from concepts of how the heat flow behaves in the system, it can be with a diagram.