Steam at a temperature of 134 °C is vented into an aluminum cup of mass 218 grams containing 600 grams of water both at 20 °C. The final temperature of the water (original condensed) and the aluminum cup is 80 °C. Cw=1 cal/g-C, Csteam = 0.48 cal/g-C, CAI = 0.215 cal/g-C, Lsteam = 539 cal/g What is the mass of the steam condensed in grams?

Steam at a temperature of 134 °C is vented into an aluminum cup of mass 218 grams containing 600 grams of water both at 20 °C. The final temperature of the water (original condensed) and the aluminum cup is 80 °C. Cw=1 cal/g-C, Csteam = 0.48 cal/g-C, CAI = 0.215 cal/g-C, Lsteam = 539 cal/g What is the mass of the steam condensed in grams?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.3P

See similar textbooks

Similar questions

Question : Determine the units of the quantity s ̄/Ru, where s ̄ is the molar specific entropy and Ru is the universal gas constant. Explain your answer please
0.05 kg of steam at 15 bar is contained in a rigid vessel of volume 0.0076 m 3 , what is the temperature of steam? If the vessel is cooled, at what temperature will the steam be just dry and saturated? The cooling is continued until the pressure in the vessel is 11.0 bar. Calculate the final dryness fraction of steam and heat rejected between initial and final states.
1. Saturated steam at a pressure of 25 psia is sprayed into a stream of moist air. The initial condition of the air is 55 dry-bulb temperature and 35 F de-point temperature. The mass rate of air flow is 2000 lb per min. Barometric pressure is 14.696 psia. Determine how much steam must be added in lb per min to produce a saturated air condition, b) the resulting temperature of the saturated air.
Just before midnight, when the air temperature of 10.0ºC, Karl stops and fills the 0.0600 m 3 gastank in his car. At noon the next day, when the temperature has risen to 32ºC, Karl finds a puddle ofgasoline (βgas = 3 x 10 -4 ºC -1 ) beneath his car.(A) How much gasoline spilled out of Karl's car? (assume that there was virtually no changein the volume of his tank)
During processing in a steel mill, a 375kg steel casting at 800 degrees is quenched by plunging it into a 500-gal oil bath, which is initially 75 degrees . After the casting cools and the oil bath warms , what is the final tempertature of the two? The weight per unit volume of the oil is 7.5 lb/gal.
50 liters at 40 °C temperature and 200 kPa pressure initially in a piston cylinder Assemblyliquid water is available. Then, until the water evaporates completely at constant pressureheatsa. What is the mass of water?b. Calculate the final temperature of the water.c. Calculate the total enthalpy change.d. Taking into account the phase change process saturation lines in the T-v diagramyour show.
Explain T-v diagram of constant-pressureb phase-change processes of a pure substance at various pressures 0.003106 (numerical values are for water).
A 5L rigid container contains Acetylene initially at gage pressure and temperature of 100 KPa and 300 K, respectively. Because of the leaks in the fittings of the vessel, the gage pressure dropped to 80KPaand the temperature decrease to 200K, determine the mass of the Acetylene that leaked out.
Natural gas, with the thermodynamic properties of methane, flows in an underground pipeline of 0.6 m diameter. The gage pressure at the inlet to a compressor station is 0.5 MPa; outlet pressure is 8.0 MPa (gage). The gas temperature and speed at inlet are 13C and 32 m/s, respectively. The compressor efficiency is η = 0.85. Calculate the mass flow rate of natural gas through the pipeline. Label state points on a Ts diagram for compressor inlet and outlet. Evaluate the gas temperature and speed at the compressor outlet and the power required to drive the compressor.
Carbon dioxide of mass 0.9 kg is contained in a vessel at a pressure of 4 MPa and atemperature of 500 °C. The gas is allowed to expand into an empty connected vessel, duringwhich its temperature falls to 120 °C. The combined volume of the two vessels is 0.45 m3.Determine (i) the initial volume of the carbon dioxide, (ii) its final pressure and (iii) thepolytropic index ‘n’ of the expansion process. Carbon dioxide has a molecular weight of 44 and the universal gas constant is 8314 Jkmol-1K-1.
Q1 / (0.2562m3) of saturated vapor at (2MPa). The ratio of dryness (0.9) expands the polytropia relationship (= Pv1.25) to (7bar). Calculate: According to V1-1 ms, 2- 02, Q 12, W 12, 2012 -3 X2 4- Find the final state of steam
Mr Luda wants to understand further about a newly created gas. The gas is initiallyat a pressure of 90 kPa, volume of 1.258 m3 and temperature of 10°C (State 1).The gas undergoes a 3-step process in which it is first compressed isothermally toa pressure of 400 kPa and volume of 0.283 m3 (State 2), then expanded at constantpressure back to its original volume (State 3). Finally, the gas is returned to itsoriginal State 1 by cooling at constant volume.a) Sketch the cycle of this system on a P – V diagram.b) Calculate the work done (in kJ) for each process step.c) Determine the total work done for the three-process cycle.d) State whether the work done is on or by the system.