Steam condensing at 120°C (h = 2203 kJ/kg) on the shell side of (1 shell and 12 thin-walled tubes) heat exchanger. Water (18 °C, C =4180 J/kg.°C) enters the tube @ 3.4 kg/s ấnd the temperature difference between the two fluids at the exit is 57°c, assume LMTD correction factor of 1.0, for each tube: length = 2.7 m, diameter = 2.4 cm. What is the rate of condensation of steam (kg/min) ?

Steam condensing at 120°C (h = 2203 kJ/kg) on the shell side of (1 shell and 12 thin-walled tubes) heat exchanger. Water (18 °C, C =4180 J/kg.°C) enters the tube @ 3.4 kg/s ấnd the temperature difference between the two fluids at the exit is 57°c, assume LMTD correction factor of 1.0, for each tube: length = 2.7 m, diameter = 2.4 cm. What is the rate of condensation of steam (kg/min) ?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.18P

See similar textbooks

Similar questions

10.1 In a heat exchanger, as shown in the accompanying figure, air flows over brass tubes of 1.8-cm 1D and 2.1-cm OD containing steam. The convection heat transfer coefficients on the air and steam sides of the tubes are , respectively. Calculate the overall heal transfer coefficient for the heal exchanger (a) based on the inner tube area and (b) based on the outer tube area.
Water flowing in a long, aluminum lube is to be heated by air flowing perpendicular to the exterior of the tube. The ID of the tube is 1.85 cm, and its OD is 2.3 cm. The mass flow rate of the water through the tube is 0.65kg/s, and the temperature of the water in the lube averages 30C. The free-stream velocity and ambient temperature of the air are 10m/sand120C, respectively. Estimate the overall heat transfer coefficient for the heat exchanger using appropriate correlations from previous chapters. State all your assumptions.
Hot water flowing at 0.015 m3/min enters the tube side of a counter current shell & tube heat exchanger at 80 C and leaves at 50 C. Cold oil flowing thru the shell at 0.05 m3/min, with density 800 kg/m3 and specific heat of 2.0 kJ/kg K, enters at 20 C. Consider water specific heat at 4.2 kJ/kg K and density of 988 kg/m3 at above condition, what is the approximate Log Mean Temperature Difference (LMTD)? Show the temperature profile completely labeled.
Heat transfers Air is to be heated from 15 C to 270 C, as it flows through a tube 25mm diameter at average velocity 30 m/s. The tube surface is maintained at 280 C and the air is to be provided at rate 0.013 kg/s. Take the water properties k=0.0336 W/m.C , υ = 25.9× 10-6 m2/s , Cp=1.014 kJ/kg.C , ρ = 0.8826 kg/ m3 , Pr=0.689 . Determine the following The necessary tube length Heat transfer coefficient Heat transfer rate
A long thin-walled double-pipe heat exchanger with tube and shell diameters of 2 cm and 4 cm, respectively, is used to condense refrigerant-134a by water at 20 C. The refrigerant flows through the tube, with a convection heat transfer coefficient of hi = 4000 W/m2 K.A 1-mm-thick layer of limestone (k = 1.2 W/mK) forms on the outer surface of the inner tube. Water flows through the shell at a rate of 0.4 kg/s. Determine the overall heat transfer coefficient U of this heat exchanger with and without the fouling factor, and the error in U introduced by neglecting the fouling factor. Comment the fouling effect on this heat exchanger.
Concentric Tube Heat Exchanger What are thermal and hydrodynamic entrance length? Are either (or both) of them an issue for the experiment? Why or why not?
A shell-and-tube heat exchanger with 1-shell pass and14-tube passes is used to heat water in the tubes with geothermal steam condensing at 1208C (hfg 5 2203 kJ/kg) on the shellside. The tubes are thin-walled and have a diameter of 2.4 cmand length of 3.2 m per pass. Water (cp 5 4180 J/kg?K) entersthe tubes at 228C at a rate of 3.9 kg/s. If the temperature difference between the two fluids at the exit is 468C, determine(a) the rate of heat transfer, (b) the rate of condensation ofsteam, and (c) the overall heat transfer coefficient.
Q1) A heat exchanger is to be designed to heat 32/68 mixture of ethylene glycol and water from 24 ᵒC to 55 ᵒC by a hot water stream from 79 ᵒC to 42 ᵒC. Flow rate of cold stream is 20 kg/s. Inlet pressure for both stream is 50 psi and the maximum pressure drop of 10 psi for cold stream and 8 psi for hot water are permissible. Report valid assumptions made for the design and give required justification. Estimate Heat Transfer, Corrected LMTD, Tube bundle diameter (Using TEMA standards and Codes) and Tube cross sectional area Heat transfer coefficient Overall heat transfer coefficient Pressure Drop (Shell side & Tube Side)
Air enters a cooler at 1450C and at a pressure of 3 bar and is cooled to 450C by passing through tubes of 10 mm inside diameter surrounded by water which enters the cooler at 150C and exits at 300C. Assuming the heat exchanger is counter flow, find: I) The mean temperature difference. ii) If the air velocity is limited to 6.5 m/s, what is the required length of tube? Neglect the resistance of the tube and assume water side heat transfer coefficient is 232 W/m2K.
Answer this ASAP The diameter of the tube is 25 mm. The specific heat of water is 4.18 kJ/kg.°C. The overall heat transfer coefficient is 0.7 kW/m².°C. 1.Heat transfer surface area 2.Heat exchanger effectiveness (E) 3.NTU 4.Required length of tube 5.Briefly describe the type of flow used in the picture
A long thin-walled double-pipe heat exchanger with tube and shell diameters of 1.0 cm and 2.5 cm, respectively, is used to condense refrigerant-134a by water at 20°C. The refrigerant flows through the tube, with a convection heat transfer coefficient of hi = 4100 W/m2·K. Water flows through the shell at a rate of 0.3 kg/s. Determine the overall heat transfer coefficient of this heat exchanger.