Strength of Materials A cantilever beam of a structure is loaded as shown in Figure below. As consultant engineers, proposed to your client 2 sections for the beam so that deflection is less than 75 mm. You are also required to perform a bending and shear stress check for each of these sections. Indicate the stresses using stress block diagrams. Note: Use data sheets of flanged sections and hollow sections as reference (manual calculations are required) 10 kN/m 7.5 m Figure a: Loading on beam Please calculate and Analyse: a) Analysis of SFD, BMD on the beam. b) Analysis of section (to manually calculate the required properties of the chosen sections). c) Analysis bending and transverse stresses and maximum deflection.

Strength of Materials A cantilever beam of a structure is loaded as shown in Figure below. As consultant engineers, proposed to your client 2 sections for the beam so that deflection is less than 75 mm. You are also required to perform a bending and shear stress check for each of these sections. Indicate the stresses using stress block diagrams. Note: Use data sheets of flanged sections and hollow sections as reference (manual calculations are required) 10 kN/m 7.5 m Figure a: Loading on beam Please calculate and Analyse: a) Analysis of SFD, BMD on the beam. b) Analysis of section (to manually calculate the required properties of the chosen sections). c) Analysis bending and transverse stresses and maximum deflection.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q: A cantilever beam of length L = 2 m supports a load P = 8.0 kN (as shown). The beam is made of wood with cross-sectional dimensions 120 mm x 200 mm. Calculate the shear stresses due to the load P at points located 25 mm, 50 mm, 75 mm, and 100 mm from the top surface of the beam. From these results, plot a graph showing the distribution bottom of shear stresses from top of the beam.
The floor system of a residential building (LL=1.9KPa) consists of 125mm thick reinforced concrete slab (unit weight = 23.6 KN/m^3) resting on three 8 m spanned RC floor beams spaced at 1.5 meters on centers. Size of RC beam is 200mm x 450mm. NSCP 2015 Load factors: 1.2DL & 1.6LL. Assume simple supports. Calculate the ultimate/factored live load in KN/m? Express your answer in 1 decimal place.
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER 1. From a 12.00 meter bridge span, a truck and trailer combination crosses with an axle loads of 10, 20, and 30 kN separated respectively by distances of 3 and 5m. What is the nearest maximum moment developed in the span? a. 105.41 kN.m b. 101.45 kN.m c. 104.15 kN.m d. 100.54 kN.m
Determine the largest weight W (in lb) that can be supported safely by the structure shown in the figure. The working stresses are 15236 psi for the steel cable AB and 881 psi for the wood strut BC. Neglect the weight of the structure. Round off the final answer to two decimal places.
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER From a 12.00 meter bridge span, a truck and trailer combination crosses with an axle loads of 10, 20, and 30 kN separated respectively by distances of 3 and 5m. What is the nearest maximum shear developed in the span? a. 45.00 KN b. 50.00 kN c. 60.00 KN d. 30.00 KN What is the nearest maximum shear developed in the span? a. 45.00 KN b. 50.00 kN c. 60.00 KN d. 30.00 KN What will be the nearest moment with reference from the left of the 10kN loading? a. 45.00 kN b. 25.75 kN c. 37.50 kN d. 61.25 kN.m
A 5-kip crate is supported by a pulley system and a horizontal force P.a) Find P and the angle α. Report your answer in kips (1 kip = 1000 lbs).b) For this problem if you double the weight of the crate, will the force P double? Briefly explain why or why not.
Please answer in 30 minutes. STRENGTH OF MATERIALS (Please write the complete solutions and FBDs completetely and correctly. No long explanation needed.Thumbs up will be given) A loaded beam, 60 mm wide by 200 mm high and 8 in long, has the shear and moment diagrams as shown below. (a) Determine the magnitude, type and location of the maximum flexural stress (b) Determine the type and magnitude of stress in a fiber 40 mm from the top of the beam at a section 2.5 m from the left end, Express final answers in MPa. (Use I=bh3/12
Calculate the nominal moment strength of a reinforced concrete beam 240 mm x 480 mm if at failure of the concrete compression strain is 0.003 and the tensile strain=0.005. The flexure bars are 20 mm in diameter enclosed by 10 mm stirrups. Use f'c = 22 MPa and fy = 420 MPa. Express your answer as a whole number in the unit of kN.m.
A concrete block is supported by two guy wires attached to an anchor ring as shown. a.Determine the resultant force on the anchor ring. b.Angle of the resultant force with respect to the horizontal axis. c.Weight (W) of the concrete block with a factor of safety of 1.25 to prevent uplift.
Can someone please solve this? Find load function functions and draw load effect diagrams? Fx=4.5KN.Fz=2.5 KNMB = 2.5 KNm.a= 1.6M.
A hollow box beam has an outside dimension of 400 mm x00mm and inside dimension of 300 mm x 500 mm (uniformthickness of 50 mm) has a fixed ended span of 6 m.1. Compute the plastic section modulus.2. Compute the plastic moment capacity of the beam.3. Which of the following gives the safe uniform loaddistributed horizontally that the beam could carry beforecollapse if Fy = 250 (Plastic Analysis using Virtual Work Method) show complete and detailed solution pls.
Calculate and illustrate the magnitude loading in kN/m acting at beam CF. Thank you