STRENGTH OF MATERIALS (Please write the complete solutions, FBD and answer in 4 decimal place. Rate/thumbs up will be given. For the given loaded truss, the allowable tensile stress in any member is up to 800 MPa while the allowable compressive stress is up to 650 MPa. The reduced stress in compression is specified to reduce the danger of buckling. Determine the minimum cross-sectional area of member BE. 6m 3m A 4m C 4m E 4m G 4m TRA 96 kN 200 kN 96 kN RH

STRENGTH OF MATERIALS (Please write the complete solutions, FBD and answer in 4 decimal place. Rate/thumbs up will be given. For the given loaded truss, the allowable tensile stress in any member is up to 800 MPa while the allowable compressive stress is up to 650 MPa. The reduced stress in compression is specified to reduce the danger of buckling. Determine the minimum cross-sectional area of member BE. 6m 3m A 4m C 4m E 4m G 4m TRA 96 kN 200 kN 96 kN RH

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find all the member forces and state wheather tension or compression Hand written please ( neat and clean)
A simply supported concrete beam 6m long is reinforce with four-28 mm diamgram tension bars. The beam has a width of 300mm and over all depth of 400.the steel covering to the centroid of the renforcement is 70 mm fc=30mpa and fy 418mpa A .draw a stress diagram B.compute for the ultimate capacity of the beam
A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforced with steel area of 2263 sq. mm at the bottom, and 1232 sq. mm on the top. Take d' = 70 mm, fc' = 21 MPa, and fy = 345 MPa. b) What is the value of fs' (actual stress of the compression bars)
Engineering Mechanics Topic: Truss Analysis – Method of Section Show your complete solution and draw again the figure. Solution (internal forces) and include what type of force if it is tension or compression but always assume tension. RA or AV is okay and fine. ps. it is fine whether the final answer is positive or negative THANK YOU! also include if it is to the left or to the right and if it's clockwise (+) or counterclockwise (-)
b=4a Allowable stress 300 MPa Size the beam? Note: Show the calculations in detail
A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforced with steel area of 2263 sq. mm at the bottom, and 1232 sq. mm on the top. Take d' = 70 mm, fc' = 21 MPa, and fy = 345 MPa. determine 1.) a 2.) the value of fs' (actual stress of the compression bars) 3.) value of ρbalance 4.) Mu
1. A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. a. Determine the limiting tensile steel ratio for a tension controlled condition in positive or negative bending with the given material strengths. ρt = ________ in 5 decimal places (ex. 0.00001) b. Determine the design moment capacity of the beam in positive bending. = ____kN∙m (whole number) c. Determine the design moment capacity of the beam in negative bending. = _____ kN∙m (whole number)
20) A rectangular section is limited to a size of b = 350 mm and d = 630 mm to carry a dead load moment of 350 kN‧m and a live load moment of 600 kN‧m. Assume that bars in compression will be placed at 80 mm from the compression face. Given f’c = 28 MPa and fy = 415 MPa. Load factors are 1.2 for dead load and 1.6 for live load for ultimate strength design. Determine the amount of compression reinforcement required if the tension reinforcement is 6,870 mm2 maintaining a tensile strain of 0.005.
Determine the maximum tensile or compressive stresses in the beam due to bending. The section has a base b= 140 mm and h= 240 mm PLACE THE ENTIRE PROCEDURE
Show step by step, please Determine the factored uniform line load, wu, acting on girder HK.
What is the internal force acting on member DF, EF and EG? Please dictate if its in compression or in tension. Complete solutions please.
Calculate the stresses in members AB, DF, and BD. Given:FAB = 51.22 kN (C)FDF = 50 kN (C)FBD = 32.98 kN (C)d = 0.05 m