Suppose you have an LFSR with state bits (also known as the seed) (85, 84, 83, 82, 81, 80) = (1, 0, 1, 0, 0, 1) and tap bits (also known as feedback coefficients) (P5, P4, P3, P2, P1, Po) = (1, 0, 0, 1, 0, 1). What are the first 12 bits output by this LFSR? Please enter your answer in the form of unspaced binary digits (e.g. 010101010101). These come in order S08182... $11.

Suppose you have an LFSR with state bits (also known as the seed) (85, 84, 83, 82, 81, 80) = (1, 0, 1, 0, 0, 1) and tap bits (also known as feedback coefficients) (P5, P4, P3, P2, P1, Po) = (1, 0, 0, 1, 0, 1). What are the first 12 bits output by this LFSR? Please enter your answer in the form of unspaced binary digits (e.g. 010101010101). These come in order S08182... $11.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Consider two raster system with the resolution 640 * 480 and 1280 * 1024. How many pixels could be accessed per second in each of these systems by a display controller that refreshes the screen at a rate of 120 frames per second? What is the access time per pixel in each system?
Computer Science Consider the following RISC-V code. addi x9, x8, 0 addi x10, x0, 0 addi x11, x0, 0 L: lw x12, 0(x9) add x10,x10,x12 addi x9,x9,4 addi x11,x11,1 addi x13,x0,20 blt x11,x13,L s w x17, 16(x9) Answer the following questions: a) How many instructions will be executed in hardware? b) How many sequential instructions are there? c) How many control (branch) instructions are there? d) What is the total number of cycles needed to execute these instructions and the CPI, if no branch prediction is implemented? e) What is the total number of cycles needed to execute these instructions and the CPI, if I implement a “Always Taken” predictor. f) Repeat Q5 with “Always Not Taken” Predictor.
Suppose each bit change in a 4-bit ADC represents a level of 0.15 m. What would the 4 bits be for a level of 1.7 m? Suppose the 4 bits were 10002. What is the range of possible levels?
Draw suitable diagrams for frame relay format and address field format, explain the followings with its tasks in frame relay address. CIR b) DLCI c) DE d) EIR
Write a program that acquires data from a data source and calculates and displays the Discrete FourierTransform associated with that data. In this case, the Arduino will generate a signal, that is sampled by the ADC and then sent to the computerover the serial port. The Arduino code is : int lookup_index = 0; #define SIN_FREQ 100 long sin_freq = SIN_FREQ; #define LOOKUP_ARRAY_SIZE 128UL #define PWM_RESOLUTION 8 #if PWM_RESOLUTION <= 8 #define PWM_t uint8_t #else #define PWM_t uint16_t #endif PWM_t *lookup_array; // lookup array for sin(2pi f t) PWM_t lookup_array1[LOOKUP_ARRAY_SIZE] = { 127, 133, 139, 146, 152, 158, 164, 170, 176, 181, 187, 192, 198, 203, 208, 212, 217, 221, 225, 229, 233, 236, 239, 242, 244, 247, 249, 250, 252, 253, 253, 254, 254, 254, 253, 253, 252, 250, 249, 247, 244, 242, 239, 236, 233, 229, 225, 221, 217, 212, 208, 203, 198, 192, 187, 181, 176, 170, 164, 158, 152, 146, 139, 133, 127, 121, 115, 108, 102, 96, 90, 84, 78, 73, 67, 62,…
Convert the bit stream 1 0 1 0 1 1 0 1 0 1 for the following schemes NRZ-L NRZ-S UNIPOLAR-RZ BIPOLAR-RZ
What are the drawbacks of using MIPS or FLOPS as a system throughput metric?
Suppose, BanglaLink has 4 voice channels, each of 60Mbps. They use synchronous TDM to multiplex these channels. If 3 characters at a time are multiplexed (3 characters in each output slot), Draw the first two output frames with arbitrary inputs.
Check if the code word is correct, assuming they were created using an even parity Hamming Code. If one is incorrect, indicate what the correct code word should have been. Also, indicate what the original data was. 01010101011 Find the chip for the network with 8 stations by using the following information. W1 = [-1]
What is the shortcoming of using MIPS
Explain how Bresenham’s Algorithm takes advantage of the connectivity of pixels in drawing straight lines on raster output. Use suitable examples. Consider two raster system with the resolution 640 * 480 and 1280 * 1024. How many pixels could be accessed per second in each of these systems by a display controller that refreshes the screen at a rate of 60 frames per second? What is the access time per pixel in each system? Consider a raster system with the resolution 1024 * 768 pixels and the color palette calls for 65,536 colors. What is the minimum amount of video RAM that the computer must have to support the above-mentioned resolution and number of colors? An object is in location (1,3), (1,6), (3,3) and (3,6). Do two repeated translation operations on the object with the scaling factors, (2,1) and (4,3). Write the new positions. An object is in location (0,0), (1,0), (0,1) and (1,1). Write the new positions after shearing the object about x-direction. Take shear parameter along…
Write an embedded C program to transmit 7-bit data with two stop bits and even parity at 9600 Baud rate using ATmega32. Assume an operating frequency of 8 MHz.