2. A water tank is fitted with a drain and outlet pipe as shown in the figure. Thesystem has 82 feet of cast iron pipe of 1-½" diameter. Determine the flow ratethrough the pipe. All fittings are threaded and regular.f = 0.034Kentrance = 0,5Kreturn bend = 1.5Ketbow = 1.4Kytobe vatve = 10Kexit = 1.015 ft.Fully openglobe valveKentranceKethowKesnPondKetum hend

Given data kentrance=0.5 kreturn bend=1.5 kelbow=1.4 kglobe valve=10 kexit=1 D=1.5in.=0.125ft L=85ft…

Answered: system has 82 feet of cast iron pipe of…

Engineering

Civil Engineering

system has 82 feet of cast iron pipe of 1-" diam through the pipe. All fittings are threaded and regu K.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SHOW COMPLETE SOLUTION AND FINAL ANSWER INTO 3 DECIMAL PLACES 3. A large pipe called penstock in hydraulic work is 1.5 m in diameter. Here it is composedof wooden staves bound together by steel hoops each 300 mm2in cross sectional area, and is used to conduct water from a reservoir to a powerhouse. If the maximumtensilestress permitted in the hoops is 130 MPa, what is the maximum spacing between hoops under a head of water of 30m? Use density of water equal to 1000 kg/m3
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. *12.9517*99.9358*30.4889*39.5136 What gage pressure p1 in kPa, is needed to provide the given flow rate? *1121 kPa*1692 kPa*1328 kPa*1725 kPa Please answer with complete and detailed solutions. thank you. ASAP
(b) FIGURE Q2 shows a siphon used to drain water from a large reservoir. The diameters of the nozzle and the pipe are given by ddnn = 25 mm and ddpp = 50 mm, respectively. If the distances are given by XX = 4.6 m and YY = 0.9 m, calculate: (i) The flow rate through the nozzle (ii) The pressure at points A and B
The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is60 litre/s. The volume of the water in the pipe bend is 50 litres and the pipe bend isinstalled in a vertical plane. The head loss from point 1 to 2 is 0.44m. Calculate the xand y for components of the thrust block to hold the pipe bend.
A 12-inch by 6-inch Venturi meter is installed in a vertical pipeline carrying water as shown inthe Figure C. The flow is upward through the meter. A differential manometer containing fluid,with sp.gr 1.67, is attached to inlet and throat, the difference z in gage levels being 5.76 ft.Neglecting loss of head, write energy equation from inlet to throat of meter. Also write stepby step equation of the differential gage between inlet and throat and combine the twoequations to compute the discharge
1. Determine the minimum height of the turbine when the blades are turning.2. Determine the maximum height of the turbine when the blades are turning. Explain your answer.3. Determine the diameter of the circle that is swept by the turning blades.4. Determine the area of the circle that is swept by the turning blades by using the formula: Area =π x (radius)^2, where π= 3,14.5. Determine the circumference of the circle that is swept by the turning blade. Blades by using theformula: Circumference = 2x π x radius, where π= 3,14. Round off to the nearest metre.
Based on the layout of the water supply system, as show in Figure 1, flow through the delivery pipe, Q = 2.50 cfs and diameter of the pipe, D = 2.65 inch with e = 0.015 inch. Ingore the minor pressure losses and use the following formulae to calculate the major pressure losses. The velocity of flow through the pipe and the friction factor, f, range are estimated to be nearly. Use g = 62.4 lb/ft^3 for water and use Moody's diagram. Water temperature is 20°C (68°F).
Three pipes are connected in series. The first pipe has a diameter of 500 mm and a length of 600 m. The second pipe has a diameter of 400 mm and a length of 500 m. The third pipe has a diameter of 300 mm and a length of 200 m. Use f = 0.02 for all pipes. If Q=0.8 m^3/s, What is the equivalent diameter, in mm, of a single pipe having the same properties that could replace the three pipes? Round off to the neares whole number.
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014 *12.9517*99.9358*30.4889*39.5136 What gage pressure p1 in kPa, is needed to provide the given flow rate? *1121 kPa*1692 kPa*1328 kPa*1725 kPa
Q2. A 200 mm x 100 mm venturimeter is provided in a vertical pipeline carrying oil of S = 0.9. The flow is in the upward direction. The throat is above the inlet by 0.25 and the differential manometer shows a gauge deflection of 0.25 m of Hg. Determine,(a) Discharge of oil (b) The pressure difference in N/m”2 between entrance and throat by using basic Bernoulli's equation. Take Cd = 0.98*
Convert all units in SI. Round off to 2 significant figures. Use Francis Formula. A sharp-created weir 2ft high extends across a rectangular channel 8 ft wide conducting irrigation water. If the measured head is 4 3/4 in., determine the discharge.
A discharge of 750 liters/sec flows through a pipe having a diameter of 400 mm and a length of 65 m long. Compute the following hand losses in the pipe in meters.1. Using Manning’s Equation with n = 0.013. a. 8.44b. 8.96c. 7.50d. 7.182. Using Darcy Weisback formula with f = 0.012. a. 3.54b. 2.15c. 3.17d. 2.753. Using Hazen Williams formula with C = 100. a. 7.45b. 6.12c. 7.86d. 7.01