1.With the help of illustration given below, identify the practical application where this converter is used andimplement this knowledge in solving the problem if the value of inductors are given as L1 equal to L2 as 15 µ henry,the value of capacitance is given as 3uF and resistance is 1 ohm. The direct current input voltage has a value ofVdc given as 250V, the output voltage frequency is given as 7.25Khz.The turn off time of the SCR is 15.8 us.Solve/Evaluate the final answer for the followinga)Resonant value of frequencyb) Turn off time(available)c)Maximum value of frequency permittedd) Time instant at which the load current is maximumT1L1VacL2T2Vo (t)Khell

We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Answered: T1 L1 Vác L2 R T2 Vo (t) 享

Engineering

Electrical Engineering

T1 L1 Vác L2 R T2 Vo (t) 享

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

in steady state Operation of Boost DC-DC Converter , Identify the component in the converter, which exhibits the highest power loss. Provide a proper reason for your answer. What is the duty ratio (D) How can it effects on the converter output (Vo) Explain the relation between the output power and system efficiency. What is the maximum voltage occurs across the switch in your practical results? Is there any difference between practical and theoretical results? Comment. 5. Compare between control characteristics of the buck and boost converters
An inductor is energized as shown in the circuit in the figure. The resistance in the circuit its value is R = 25 Ω, applied voltage VCC = 100 V, t1 = 5 ms and T = 50 ms. Transistor and diode Assume ideal. Turning of inductor current to zero in each switching period wanted. In this case, with the largest inductor that can be chosen, how many W is the power consumed in the resistor will it?
design a battery charger for safe operation in a damp garage environment to use for charging your 12 VDC car battery. Design specifications include: (a) Input is a 110rms VAC. (VP=110x ) at 60 Hz from a three wire service that meets the National Electrical Code. (b) Output is a nominal 12 volts VDC at the cathode of the diode. (c) Specify a resistor, R, to limit the maximum battery charging current to 10 amperes into the 12 volt car battery assuming the battery is completely dead (0 volts) when you first connect the charger. (d) There is no ripple voltage design specification. Explain why this is unnecessary in this application. (e) The battery charger case is metal. (f) Assume a diode with VF = 0.7 V (g) The fuse in the primary circuit is to protect the power supply from a short-circuit at the battery terminals either from total battery failure or accidentally short circuiting the charging cable to ground…
An ideal boost converter is required to have a constant output voltage of 12 V at 24 W load.The input voltage varies from 2.7 to 4.5 V (as in a battery cell). Select a switching frequency of100 kHz. The value of the inductance in the boost converter is 2.2 uH. Determine:(a) The range of duty cycle that the converter will operate with (hint: mode?), and(b) The minimum value of the output capacitance such that the pk-to-pk load voltage rippleis less than 2%.
Power Electronics. In the Buck-Boost DC-DC converter circuit:Welding voltage [40-80]VSwitching frequency (f) 25khzVoltage between load terminals 55VCapacitance value 470uFLoad current value [10-25]A Under these conditions, which is the lowest ripple (delta IL) amount of the current passing through the coil (L) in Amps for the lowest L inductance value that can keep the DC-DC converter in a continuous current state? A) 23.9803B) 118.75C) 84.3750D) 47.5E) 59.9507F) 33.75
100 V battery voltage to 75 V need a da-da circuit to reduce the voltage is heard. Transducer inductance 800 μH and loadresistance is given as 25 Ω. Power switch transmission duration is 20 μs, the circuit is in continuous conduction works. According to this; a) a) By specifying the name of the da-da converter used, draw b) Gate sign (vgs), switch voltage (vds), diode voltage Plot (vD), and inductance current (iL) c) Find the switching frequency and the transmission time of the diode.
Q2) B) In a step-up converter, the duty ratio is adjusted to regulate the output voltage at 48V. The converter is supplied by a solar cell panel where its output voltage varies in a wide range as shown in the following V-I characteristics (Fig.PE-1). The maximum power output of the converter is 120 W. For stability reasons, it is required that the converter always operate in a CCM mode. The switching frequency is 50kHz. Assuming ideal components and C as very large, calculate the maximum value of L that can be used.
a)A 3-phase full converter delivers power to a load R=50 ohms. the source voltage is 400V,50Hz.For a firing-angle delay of 45 degrees, find the power delivered to the load R.(b)A single phase fully-controlled bridge converter supplies a load drawing constant ripple free current. if the firing angle is 30degrees.find the input power factor.
The circuit diagram of step-up type DC-DC converter is given below. It is assumed that the output capacitor is large enough and the output voltage is constant. (Consider that there is no circuit losses.) Select an inductance value for the CCM operating state of the circuit. With this inductance value, taking into account the minimum input voltage and minimum output current, calculate the value of C so that the output voltage has a fluctuation of 1%.
amplifier (boost) DC-DA converter circuit, given below; 1- Source voltage (E) value: In the voltage range of [A B] (Volts) 2- Switching frequency (f) value: M kHz 3- Voltage between load terminals (Vload) F (volt) 4- Capacity value is 470 (microF) 5- Pload>= H(watts) consumed per load In which case below do you see the lowest L inductance value in microH that can keep the DC-DC converter in a continuous current state under the conditions? A=25 VOLT B=40 VOLT M= 25kHz F = 55 VOLT H=15 Watts a) 454.5475 b) 382,045 c) 263.62 d) 128.5 e) 581.81
Explain the principle of operation of the Multiphase converter, with the aid of suitable diagrams
Discuss the difference between Passive and Active Components? Give examples