Table 1 shows the various quantities of materials needed for several different concrete mixes. Mix #1 is the 'standard' mix without the use of admixtures, while both Mixes #2 and #3 were produced with the aid of one (1) specific type of admixture. i. State the name/type of this specific admixture that was used for Mix #2 and Mix #3. ii. Explain the two (2) main functions of this admixture. For each

Table 1 shows the various quantities of materials needed for several different concrete mixes. Mix #1 is the 'standard' mix without the use of admixtures, while both Mixes #2 and #3 were produced with the aid of one (1) specific type of admixture. i. State the name/type of this specific admixture that was used for Mix #2 and Mix #3. ii. Explain the two (2) main functions of this admixture. For each

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The design of a concrete mix requires 1173 kg/m3of gravel in dry condition,582 kg/m3of sand in dry condition, and 157 kg/m3of free water. The gravelavailable at the job site has a moisture content of 0.8% and absorption of1.5%, and the available sand has a moisture content of 1.1% and absorptionof 1.3%. What are the masses of gravel, sand, and water per cubic meter thatshould be used at the job site?
a) What are the broad types of admixtures? b) What do you mean by concrete mix design; what are the major factors that must be considered while designing concrete mixes? c) Name various methods used for concrete mix design worldwide? Which method is commonly used Pakistan? GIVE ME ANSWER ALL PARTS. SIR, PLS GIVE ME PROPER AND CORRECT ANSWER WITH FULL DETAILS. THANKS SUBJECT: CONCRETE TECHNOLOGY
A concrete aggregate mix must contain at least 31% sand by volume for proper batching. One source of material, which has 25% sand and 75% coarse aggregate, sells for $3 per cubic meter (m3). Another source, which has 40% sand and 60% coarse aggregate, sells for $4.40/m3. Determine the least cost per cubic meter of blended aggregates.
. As a material engineer in charge of designing concrete mix and facing the following problems, which admixture would you use in each case during mixing or at the jobsite? a. There is a large quantity of freshly mixed concrete and the work at the jobsite had to stop because of rain. b. More time is expected to be needed for finishing concrete. c. The structure is subject to freezing. d. Concrete is to be around tightly spaced reinforcing steel. e. Concrete mix will be hauled a long distance. f. High early strength concrete is required, but not necessarily high ultimate strength.
Q2 b Concrete mix can be proportioned using a nominal mix and design mix.Compare and contrast the use of a design mix as compared to a nominal mix.
Designing a concrete that will be exposed to groundwater, the chemical analysis of which is given in Table 1. is requested. a) For 1 m3 of concrete, assuming the air gap is 1%, according to the relevant impact class specified in TS EN 206 Calculate the amount of material needed. (Maximum grain size of A1, A2, A3 aggregates to be used in the mixture) has a diameter of 16 mm and is in SDYK state, and the physical properties and mixing ratios of the aggregates are given in Table 2.) b) The ratio of cement kneading water to be used in production is 28%, volumetric shrinkage of cement paste Calculate the shrinkage that will occur in the concrete, assuming that the absolute volume of cement is 1%. from shrinkage Find the tensile stress that will occur in the concrete due to Whether cracks will occur in the concrete due to shrinkage, Considering the static elasticity modulus (secant modulus) of the concrete given below in the “stress-strain” diagram. take it and check it. Note: In the…
Working on major construction project that requires considerable amounts of concrete to be used,you are asked to design a concrete mix following the BRE methodology. All the necessary tables forthis can be found in the Appendix. The concrete mix specifications are:o Characteristic compressive strength of 35 N/mm 2 at 28 days.o Failure rate of 2%o Previous control data yielded a standard deviation of 10 N/mm 2o CEM-I 42.5o Air-entraining is not requiredo Maximum water to cement ratio 0.40o Minimum cement content 390 kg/m 3o Required slump 50 mmo Coarse aggregate: Crushed maximum size 20mmo Fine aggregate: Uncrushed with 90% passing 600 μm sieveo Relative density of aggregates: 2.5o Coarse aggregate has 4% moistureo Fine aggregate is dry and has 1.2% absorption.o Volume of the required trial mix: 0.090 m 3Following the BRE step-by-step process estimate the water content of the mix estimate the content of aggregates, provide the estimated mix quantities
Construction management please answer all the numbers. it will be a great help to me. thank you 1. The temperature in the room in which the concrete samples must be stored before testing should not be less than 23ºC. True or False. Explain 2. Maximizing the amount of aggregate, to a certain extent, improves the quality and economy of the mix. True or False. Explain 3.
Please answer the problem. You can summarize your answer. Thank you and Godbless. Comment on the results. Compare the results with the typical values. How can the percentage of absorption affect on a concrete mix?
How does the increase of maximum aggregate size used in the concrete mix design affect the percentage of fine aggregates needed for the mix? Explain why this is the case.
The design engineer specifies a concrete strength of 3700 psi. A plant where s = 300 psi for 41 test results. Which is the required average compressive strength to be used in your mix design? a. 3900 psi; b) 4000 psi; c)4 100 psi; d) 4200 psi
The correct mix for a batch of concrete is 5:4:2 in terms of sand, gravel, and cement. The batch is to have 2200 pounds of these ingredients. How many of each are needed? Sand Gravel Cement